NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A pocket-hole waterfall table where the 45° miter isn't decorative — it wraps continuous 1x12 grain from the tabletop down the sides, so the corner has to be cut, not just assembled, correctly.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Face frame, long rails Both ends cut at 45°, ends NOT parallel, long point to long point. | 4 | 3/4" × 2 1/2" × 60" | 1x3 | ☐ |
| Face frame, short rails Both ends cut at 45°, ends NOT parallel, long point to long point. | 4 | 3/4" × 2 1/2" × 18" | 1x3 | ☐ |
| Waterfall top panels Both ends cut at a 45° bevel, ends NOT parallel, long point to long point. Cut these first — the grain match starts here. | 2 | 3/4" × 11 1/4" × 60" | 1x12 | ☐ |
| Waterfall side panels One end cut at a 45° bevel, long point measurement. Reserve the offcut from the top-panel cut as your reference so the grain wraps continuously. | 4 | 3/4" × 11 1/4" × 18" | 1x12 | ☐ |
| Bottom shelf | 2 | 3/4" × 11 1/4" × 58 1/2" | 1x12 | ☐ |
| Inside side panels | 4 | 3/4" × 11 1/4" × 14 3/4" | 1x12 | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 1x12, 8 ft Must be flat and fully acclimated — this is the waterfall panel and the shelf. No cupping or crowning. | 4 each | ☐ |
| 1x3, 8 ft The two face frames. | 4 each | ☐ |
| 1x2, 8 ft Center supports under the top and shelf. | 1 each | ☐ |
| Pocket hole screws, 1-1/4" coarse thread | 100 each | ☐ |
| Brad nails, 1-1/4" | 40 each | ☐ |
| Wood glue | 4 oz | ☐ |
| Stain, whitewash, and finishing supplies | 1 qt | ☐ |
Overall cost: $$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Drill / Driver, Miter Saw, Pocket Hole Jig. Materials: 1x3, 8 ft, Pocket hole screws, 1-1/4" coarse thread, Wood glue
Cut the 1x3 face-frame boards to length with 45° miters, ends not parallel. On the shorter boards, drill two 3/4" pocket holes on each end, positioned so the pocket hole won't be visible on the outside of the frame once assembled.
Assemble with 1-1/4" pocket hole screws and glue. Build two frames and check they're identical before moving on — any mismatch here shows up as a crooked table later.
Tools: Drill / Driver, Miter Saw, Pocket Hole Jig, Speed Square. Materials: 1x12, 8 ft, Pocket hole screws, 1-1/4" coarse thread, Wood glue
From one 1x12 board, cut the first top panel with both ends beveled at 45° — check the cut is square across the full width with a speed square, and set the offcut aside; you'll reference it for the side panel cuts. Cut the second top panel the same way.
Drill pocket holes to join the two top panels together edge to edge, and drill additional pocket holes for attaching a face frame to each side. Clamp each joint as you glue and screw it, then carefully attach the whole joined top to one of the face frames — the frame and the top should sit perfectly flush and smooth across the joint.
Tools: Brad Nailer. Materials: 1x12, 8 ft, Brad nails, 1-1/4"
Repeat the same bevel-cutting and pocket-hole process for the two side panels, using the offcuts you reserved to keep the grain direction and figure matching the top. Drill pocket holes on these too for attaching to both face frames.
Attach the two side panels to the top assembly with 1-1/4" brad nails, keeping the mitered corner tight and flush all the way across — this is the joint the whole waterfall effect depends on.
Tools: Drill / Driver. Materials: Pocket hole screws, 1-1/4" coarse thread
Attach the sides and top assembly to the second face frame, matching it up the same way as the first — the table should now stand as a mitered box with a face frame at each end.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 1x12, 8 ft, Pocket hole screws, 1-1/4" coarse thread
Cut the bottom shelf boards and drill pocket holes to join them together, plus additional 3/4" pocket holes around all sides for attaching inside the face frames.
Carefully place the joined shelf inside the frame and attach with 1-1/4" pocket hole screws, keeping the top of the shelf flush with the top of the face-frame insides as you go.
Tools: Brad Nailer, Drill / Driver, Pocket Hole Jig. Materials: 1x12, 8 ft, Brad nails, 1-1/4"
Measure and cut the inside side panels to fit. Join them together at the center with pocket holes, then place the assembly inside the face frame and nail it to the table — add screws from the bottom as well for extra hold.
Tools: Drill / Driver, Pocket Hole Jig, Random Orbit Sander. Materials: 1x2, 8 ft, Pocket hole screws, 1-1/4" coarse thread, Stain, whitewash, and finishing supplies
Make sure your 1x12s are fully acclimated to your home's moisture (they may have dried further since purchase) before measuring and cutting this step's boards to fit the inside width.
Drill a pocket hole on each end and three more along the length of each 1x2. Attach roughly 20" in from the sides, on both the top and the bottom shelf, with 1-1/4" pocket hole screws — this is what keeps a 60" span from developing a visible sag over time.
Sand the whole piece and finish with stain, whitewash, or your choice of topcoat.