NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A 1x12 cabinet whose whole front tilts forward to present the trash can — gravity keeps it closed, a lid-support chain keeps it from face-planting. No catches, no springs.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Box sides | 2 | 3/4" × 11 1/4" × 29 1/4" | 1x12 | ☐ |
| Box top | 1 | 3/4" × 11 1/4" × 18" | 1x12 | ☐ |
| Box bottom shelf | 1 | 3/4" × 11 1/4" × 16 1/2" | 1x12 | ☐ |
| Back supports | 2 | 3/4" × 2 1/2" × 16 1/2" | 1x3 | ☐ |
| Front trim, 1x2 | 2 | 3/4" × 1 1/2" × 18" | 1x2 | ☐ |
| Front trim, 1x3 | 1 | 3/4" × 2 1/2" × 18" | 1x3 | ☐ |
| Door stiles | 2 | 3/4" × 2 1/2" × 25" | 1x3 | ☐ |
| Door rails | 2 | 3/4" × 2 1/2" × 13" | 1x3 | ☐ |
| Door shelf | 1 | 3/4" × 11 1/4" × 16" | 1x12 | ☐ |
| Door side wings Cut at 45° into the two triangular wings. | 1 | 3/4" × 11 1/4" × 11 1/4" | 1x12 | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 1x12, 6 ft Box sides, top, bottom shelf, and door parts. | 2 each | ☐ |
| 1x3, 6 ft Door frame, back supports, and front trim. | 2 each | ☐ |
| 1x2, 4 ft Front trim. | 2 each | ☐ |
| Plywood, 1/4", 24" x 14-1/4" The door's panel. | 1 each | ☐ |
| Narrow hinges with flat-head screws The inexpensive flat kind — mounted at the door's bottom edge. | 2 each | ☐ |
| Knob or pull | 1 each | ☐ |
| Lid support, chain, or wire Stops the door at its open angle. Not optional — toes. | 1 each | ☐ |
| Pocket hole screws, 1-1/4" | 25 each | ☐ |
| Brad nails, 3/4" and 1-1/4", 18 ga | 60 each | ☐ |
| Wood glue | 4 oz | ☐ |
Overall cost: $$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Brad Nailer, Drill / Driver, Pocket Hole Jig, Speed Square. Materials: 1x12, 6 ft, Pocket hole screws, 1-1/4", Wood glue
Assemble the sides, top, and bottom shelf — pocket holes, 2" screws, or brads and glue all work. The bottom shelf's TOP surface sits 2-1/2" up from the floor (1-3/4" gap beneath it). Check the box square; the tilt door needs a true opening more than most doors do.
Tools: Brad Nailer, Drill / Driver. Materials: 1x3, 6 ft, Brad nails, 3/4" and 1-1/4", 18 ga, Wood glue
Attach the 1x3 back supports to hold the box square. But first decide: want to pull the can out the BACK for emptying? Then leave the CENTER back support off until the door is installed and placed — its final position depends on the can clearing it.
Tools: Brad Nailer. Materials: 1x3, 6 ft, 1x2, 4 ft, Brad nails, 3/4" and 1-1/4", 18 ga, Wood glue
Brad-nail the front trim to the cabinet face. The opening this frames is the door's home — even reveals here decide how factory-made the finished cabinet looks.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 1x3, 6 ft, Pocket hole screws, 1-1/4", Wood glue
Pocket-hole the 1x3 door frame together — 3/4" setting, 1-1/4" screws, holes on the back face.
Drill pocket holes along the door shelf's bottom edge and attach it to the frame: inset 1" from the frame edges, and held DOWN 1/8" at the bottom.
Those numbers are the mechanism. The inset lets the shelf swing into the box without striking the sides; the 1/8" drop keeps it off the cabinet floor mid-tilt. Measure them, don't eyeball them.
Tools: Drill / Driver, Miter Saw, Pocket Hole Jig. Materials: 1x12, 6 ft, Pocket hole screws, 1-1/4"
Cut the wing stock at 45° into two triangles, pocket-hole their edges, and attach to the door panel and shelf. The wings cradle the can through the tilt — without them the can leans out with the door and makes its own exit.
Tools: Brad Nailer, Circular Saw. Materials: Plywood, 1/4", 24" x 14-1/4", Brad nails, 3/4" and 1-1/4", 18 ga, Wood glue
Cut the 1/4" ply to fit inside the door frame and fasten with 3/4" brads and glue.
Tools: Drill / Driver, Random Orbit Sander. Materials: Narrow hinges with flat-head screws, Knob or pull, Lid support, chain, or wire
Hinge the door to the cabinet at its BOTTOM edge with the narrow flat hinges. Tilt it: the door and can weight should close it on its own — the source found no catch necessary, and yours likely won't need one either.
What it DOES need is the restraint: install the chain, wire, or lid support so the open angle stops where the can presents nicely and nowhere near the floor. Add the knob, sand, finish, drop the can in, and enjoy a kitchen where the trash disappeared into furniture.