NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A four-drawer 1x8 dresser on chunky 2x4 legs — every top and drawer face board is cut with a stop-block setup so every piece matches exactly.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Top boards | 9 | 3/4" × 7 1/4" × 16" | Pine | ☐ |
| Top filler pieces | 3 | 3/4" × 3 1/2" × 16" | Pine | ☐ |
| Top trim Measure and cut to fit the actual glued-up top. | 2 | 3/4" × 1 1/2" × 65 1/4" | Pine | ☐ |
| Side panels | 4 | 3/4" × 7 1/4" × 24 1/2" | Pine | ☐ |
| Legs | 5 | 1 1/2" × 3 1/2" × 28 1/2" | Pine | ☐ |
| Frame rails | 3 | 3/4" × 1 1/2" × 63 3/4" | Pine | ☐ |
| Middle frame rail | 1 | 3/4" × 2 1/2" × 63 3/4" | Pine | ☐ |
| Front middle leg | 1 | 3/4" × 3 1/2" × 24 1/2" | Pine | ☐ |
| Back blocking | 4 | 3/4" × 1 1/2" × 9 1/2" | Pine | ☐ |
| Front blocking | 2 | 3/4" × 3 1/2" × 9 1/2" | Pine | ☐ |
| Drawer sides | 8 | 3/4" × 5 1/2" × 16" | Pine | ☐ |
| Drawer fronts/backs Measure each opening individually — width equals the opening minus 2-1/2". | 8 | 3/4" × 5 1/2" × 28 3/8" | Pine | ☐ |
| Drawer bottoms | 4 | 1/4" × 16" × 29 7/8" | 1/4" plywood | ☐ |
| Drawer faces Four boards join to make each of the four drawer faces. | 16 | 3/4" × 7 1/4" × 11 1/4" | Pine | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| Pine, 1x8, 8 ft | 5 each | ☐ |
| Pine, 1x6, 8 ft | 4 each | ☐ |
| Pine, 1x4, 8 ft | 1 each | ☐ |
| Pine, 1x3, 8 ft | 1 each | ☐ |
| Pine, 1x2, 8 ft | 5 each | ☐ |
| Pine, 2x4, 12 ft | 1 each | ☐ |
| Plywood, 1/4", 48" x 48" | 1 each | ☐ |
| Euro-style drawer slides, 16", white | 4 pair | ☐ |
| Pocket hole screws, 1-1/4" | 1 box | ☐ |
| Pocket hole screws, 2-1/2" | 1 box | ☐ |
| Brad nails, 1-1/4" and 5/8" | 1 box | ☐ |
| Sandpaper, medium and fine grit | 6 sheet | ☐ |
| Stain and clear poly | 1 quart | ☐ |
Overall cost: $$$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Drill / Driver, Miter Saw, Pocket Hole Jig. Materials: Pine, 1x8, 8 ft
Set up a stop block on the miter saw and cut every top board to length so all pieces match exactly. Drill 3/4" pocket holes on all but one of the top pieces, and clamp each joint as you attach them together with 1-1/4" pocket hole screws.
Tools: Brad Nailer. Materials: Pine, 1x4, 8 ft, Pine, 1x2, 8 ft
Measure and cut 1x2 trim to fit the front and back edges of the top, attaching with glue and 1-1/4" brad nails. Cut 1x4 filler boards to match the tabletop's cut lengths and attach with brad nails and glue.
Tools: Drill / Driver, Pocket Hole Jig. Materials: Pine, 1x8, 8 ft
Cut the 1x8 side panels and join them together along the center with 3/4" pocket holes and 1-1/4" pocket hole screws. Drill 3/4" pocket holes along the sides and top for attaching to the legs and top in later steps. Build two identical side panel assemblies.
Tools: Drill / Driver. Materials: Pine, 2x4, 12 ft
Set the pocket hole jig to 1-1/2". Drill two pocket holes in the top of each leg, keeping the hole on the inside leg about 1" in so it doesn't get covered by the side panel. Attach the side panels to the legs with 1-1/4" pocket hole screws.
Build the two leg-and-side assemblies as true mirror images of each other — pocket holes in the legs face backward, pocket holes in the center panel face inward and stay hidden. Get the handedness right before drilling.
Tools: Drill / Driver
Attach the leg assemblies to the top using 2-1/2" pocket hole screws. If there's any width difference between the two sides, align the fronts perfectly and leave any discrepancy at the back where it won't be noticed.
Tools: Brad Nailer, Speed Square. Materials: Pine, 1x2, 8 ft
Check the whole assembly for square by measuring opposite diagonals before this step — the legs need to be genuinely square (not a parallelogram) to the top before the framing goes in. Attach the inner framing rails to the 2x4 legs with glue and 1-1/4" brad nails, keeping consistent spacing and rechecking for square as you go.
Tools: Drill / Driver. Materials: Pine, 1x4, 8 ft, Pine, 2x4, 12 ft
The center legs carry the drawer slides for the middle drawer pair, so they need to be square to the whole project — measure carefully. The front middle leg is 1x4 stock; the back is 2x4.
Tools: Brad Nailer. Materials: Pine, 1x3, 8 ft, Pine, 1x2, 8 ft
Cut blocking from 1x2 stock and attach to the inside back of the dresser with 1-1/4" brad nails and glue. Attach 1x3 blocking to fill in the front leg area the same way.
Tools: Drill / Driver, Pocket Hole Jig. Materials: Pine, 1x6, 8 ft, Plywood, 1/4", 48" x 48", Euro-style drawer slides, 16", white
Cut drawer sides to 16" long. Measure each drawer opening individually and subtract 2-1/2" for the front and back pieces — this should come out close to 28-3/8", but always measure your actual opening rather than trusting the number. Cut drawer bottoms to 16" x (opening minus 1"). Build the boxes with pocket holes or 1-1/4" brad nails, attaching the bottoms with 5/8" brad nails and glue.
Install the slides so the front of the slide is flush with the front of the blocking boards, leaving about 1/2" of clearance under the slide so the drawer doesn't rub on the framing.
Tools: Drill / Driver, Pocket Hole Jig. Materials: Pine, 1x8, 8 ft
Cut the drawer face boards and join them together with pocket holes. Carefully attach the assembled faces to the drawer boxes with 1-1/4" brad nails, then secure further from the inside with 1-1/4" screws. This step goes easier with a second person holding the face in position while you fasten it.
Tools: Random Orbit Sander. Materials: Sandpaper, medium and fine grit, Stain and clear poly
Sand with medium, then fine grit sandpaper. Stain and apply clear poly.