NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A floor-standing vanity with edge-glued 1x6 side panels, a pocket-holed face frame, and three real drawers on euro slides — sized to build your own top around your own sink.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Side panel boards | 6 | 3/4" × 5 1/2" × 31 3/4" | 1x6, 8 ft | ☐ |
| Side trim | 4 | 3/4" × 1 1/2" × 18" | 1x2, 8 ft | ☐ |
| Back supports | 2 | 3/4" × 2 1/2" × 32" | 1x3, 8 ft | ☐ |
| Front legs | 2 | 3/4" × 3 1/2" × 31 3/4" | 1x4, 8 ft | ☐ |
| Face frame, top/bottom | 2 | 3/4" × 2 1/2" × 26 1/2" | 1x3, 8 ft | ☐ |
| Face frame, middle | 2 | 3/4" × 1 1/2" × 26 1/2" | 1x2, 8 ft | ☐ |
| Back panel boards | 2 | 3/4" × 5 1/2" × 31 3/4" | 1x6, 8 ft | ☐ |
| Drawer slide supports | 2 | 3/4" × 1 1/2" × 31 3/4" | 1x2, 8 ft | ☐ |
| Front trim Cut to fit. | 2 | 3/4" × 1 1/2" × 35" | 1x2, 8 ft | ☐ |
| Large drawer sides | 4 | 3/4" × 5 1/2" × 16" | 1x6, 8 ft | ☐ |
| Large drawer front/back | 4 | 3/4" × 5 1/2" × 23 3/4" | 1x6, 8 ft | ☐ |
| Top drawer sides | 2 | 3/4" × 3 1/2" × 16" | 1x4, 8 ft | ☐ |
| Top drawer front/back | 2 | 3/4" × 3 1/2" × 23 3/4" | 1x4, 8 ft | ☐ |
| Drawer bottoms | 3 | 1/4" × 16" × 25 1/4" | 1/4" plywood panel, 48" x 48" | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 1x6, 8 ft | 5 each | ☐ |
| 1x2, 8 ft | 3 each | ☐ |
| 1x3, 8 ft | 2 each | ☐ |
| 1x4, 8 ft | 2 each | ☐ |
| 1/4" plywood panel, 48" x 48" | 1 each | ☐ |
| Euro style drawer slides, 16 in, pair | 3 set | ☐ |
| Drawer slide back sockets | 3 each | ☐ |
| Bin pulls | 3 each | ☐ |
| Pocket hole screws, 1-1/4" | 100 each | ☐ |
| Brad nails, 1-1/4" | 60 each | ☐ |
| Wood glue | 5 oz | ☐ |
| Primer and paint, or stain and poly | 1 set | ☐ |
Overall cost: $$$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Drill / Driver. Materials: 1x6, 8 ft, 1x2, 8 ft, Wood glue
Glue three 1x6 boards edge to edge on a flat surface for each side. Attach the 1x2 trim on top, overhanging the ends by 3/4", leaving a 2-1/2" space under the bottom trim.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 1x3, 8 ft, Pocket hole screws, 1-1/4"
Drill two pocket holes on each end of the back support boards and attach with pocket hole screws, exposed on the back.
Tools: Brad Nailer, Drill / Driver, Pocket Hole Jig. Materials: 1x2, 8 ft, 1x3, 8 ft, 1x4, 8 ft, Pocket hole screws, 1-1/4", Brad nails, 1-1/4", Wood glue
Build the face frame flat with pocket holes and pocket hole screws, then nail and glue to the front of the cabinet. Check for square with diagonal measurements.
Tools: Brad Nailer. Materials: 1x6, 8 ft, Brad nails, 1-1/4", Wood glue
Nail and glue the back panel boards to the sides and top/bottom supports, giving the drawer slides something solid to attach to.
Tools: Brad Nailer, Miter Saw. Materials: 1x2, 8 ft, Brad nails, 1-1/4", Wood glue
Measure and cut the front trim to fit, then nail and glue in place.
Tools: Brad Nailer, Drill / Driver, Pocket Hole Jig.
Build the drawer boxes with pocket holes, boxing out corners around plumbing where needed. Nail and glue the plywood bottoms on.
Tools: Drill / Driver. Materials: Euro style drawer slides, 16 in, pair, Drawer slide back sockets
Attach the drawer slides to the front 1x2 cleat and a rear end socket, following the hardware's instructions.
Tools: Drill / Driver, Jigsaw, Pocket Hole Jig. Materials: 1x4, 8 ft
Build the top from 1x boards pocket-holed together, leaving an opening sized to your own sink.
Tools: Random Orbit Sander. Materials: Bin pulls, Primer and paint, or stain and poly
Sand all surfaces, apply primer and paint or stain and poly, and add the bin pulls.