NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A wall-hung vanity cabinet with no legs at all — lag-bolted directly to studs, with vertical dividers you cut into on-site to clear your actual vanity top and sink.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Sides | 2 | 3/4" × 21 1/2" × 21 1/2" | 3/4" plywood, cabinet grade, full sheet | ☐ |
| Bottom | 1 | 3/4" × 21 1/2" × 34 1/2" | 3/4" plywood, cabinet grade, full sheet | ☐ |
| Top trim Place the nicest edge outward on the front. | 2 | 3/4" × 2 1/2" × 34 1/2" | 1x3, 10 ft total | ☐ |
| Back support panels | 2 | 3/4" × 20" × 8" | 3/4" plywood, cabinet grade, full sheet | ☐ |
| Inner vertical dividers May need cutting to clear your actual sink. | 2 | 3/4" × 21 1/2" × 20" | 3/4" plywood, cabinet grade, full sheet | ☐ |
| Back supports | 2 | 3/4" × 2 1/2" × 17" | 1x3, 10 ft total | ☐ |
| Shelves | 2 | 3/4" × 8" × 20 1/2" | 3/4" plywood, cabinet grade, full sheet | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 3/4" plywood, cabinet grade, full sheet | 1 each | ☐ |
| Edge banding, 3/4", 12 ft | 1 each | ☐ |
| 1x3, 10 ft total | 1 each | ☐ |
| Pocket hole screws, 1-1/4" | 60 each | ☐ |
| Cabinet screws, 2" | 20 each | ☐ |
| Brad nails, 1-1/4" | 30 each | ☐ |
| Wood glue | 4 oz | ☐ |
| Premade cabinet door | 1 each | ☐ |
| Euro hinges, inset for frameless cabinets, pair | 1 set | ☐ |
| Vanity top, 22" x 37" | 1 each | ☐ |
| Lag screws, 4", for hanging to studs | 6 each | ☐ |
| Wood filler | 2 oz | ☐ |
| Sandpaper, 120 grit | 3 sheet | ☐ |
| Cabinet grade paint | 1 set | ☐ |
Overall cost: $$$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 3/4" plywood, cabinet grade, full sheet, 1x3, 10 ft total, Pocket hole screws, 1-1/4"
Drill 3/4" pocket holes on the bottom and attach to the sides, pocket holes hidden on the bottom. Attach the 1x3 top trim, pocket holes hidden on top, with the nicest edge facing forward.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 3/4" plywood, cabinet grade, full sheet, Pocket hole screws, 1-1/4", Wood glue
Attach the back support panels, which carry the cabinet's hanging load, with extra pocket holes and glue.
Tools: Jigsaw. Materials: Vanity top, 22" x 37"
Place the vanity top and sink on the cabinet before installing the vertical dividers, and mark any cutout needed. Cut into the tops of the dividers with a jigsaw if the sink requires it.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 3/4" plywood, cabinet grade, full sheet, 1x3, 10 ft total, Pocket hole screws, 1-1/4", Wood glue
Measure and cut the back support boards to fit, attach in place with 3/4" pocket holes and 1-1/4" pocket hole screws and glue. Install the vertical dividers, using the 8" shelf piece as a spacing guide.
Tools: Brad Nailer. Materials: 3/4" plywood, cabinet grade, full sheet, Brad nails, 1-1/4", Wood glue
Attach the shelves with glue and brad nails to keep the interior free of visible pocket holes or screws.
Tools: Drill / Driver, Level. Materials: Lag screws, 4", for hanging to studs
Hang the cabinet to studs in the wall using the 4" lag screws, spaced as far apart vertically as possible for maximum support.
Tools: Drill / Driver, Iron for Edge Banding, Random Orbit Sander. Materials: Edge banding, 3/4", 12 ft, Premade cabinet door, Euro hinges, inset for frameless cabinets, pair, Wood filler, Sandpaper, 120 grit, Cabinet grade paint
Edge-band the exposed plywood edges, sand, fill, and finish with cabinet grade paint, then install the door with the euro hinges.