NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A slab farmhouse tabletop on purchased turned legs — skip the lathe and get a furniture-shop look with an afternoon of apron building.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Apron, ends | 2 | 3/4" × 3 1/2" × 24 1/2" | Pine | ☐ |
| Apron, sides | 2 | 3/4" × 3 1/2" × 66" | Pine | ☐ |
| Center support | 2 | 3/4" × 2 1/2" × 30 1/2" | Pine | ☐ |
| Angle supports Cut from tabletop-board offcuts, not new stock. | 4 | 3/4" × 9 1/4" × 78" | Pine | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| Turned table legs, 28-29" dining height Buy from a turned-leg supplier — this is what makes the shortcut work. Pick a profile that matches your apron width. | 4 each | ☐ |
| Pine, 1x10, 8 ft Tabletop boards. Save the offcuts — they're sized to build a matching bench. | 4 each | ☐ |
| Pine, 1x4, 8 ft Apron. | 2 each | ☐ |
| Pine, 1x3, 8 ft Center support. | 1 each | ☐ |
| Pocket hole screws, 2-1/2" | 1 box | ☐ |
| Wood glue | 6 oz | ☐ |
| Leg mounting hardware Whatever the leg manufacturer specifies — usually a corner bracket or threaded insert. | 4 set | ☐ |
Overall cost: $$$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Bar / Pipe Clamps. Materials: Pine, 1x10, 8 ft, Wood glue
Edge-glue the four 1x10 boards into a single tabletop panel and clamp on a flat, level surface. Alternate the direction of any visible grain cupping board to board so the whole panel resists warping evenly, and check the surface is flat with a straightedge before you walk away — a twist that sets in the glue is much harder to fix than one you catch now. Let it dry fully before moving on.
Tools: Drill / Driver, Pocket Hole Jig. Materials: Pine, 1x4, 8 ft, Wood glue
Build each end apron piece — this is what each pair of legs will mount to. Use pocket holes and glue at every joint, and check for square as you go.
Tools: Drill / Driver, Pocket Hole Jig, Speed Square. Materials: Pine, 1x4, 8 ft, Wood glue
Join the two end assemblies with the long side apron pieces, again with pocket screws and glue. Check the whole frame for square and for a flat sit before you go further — this apron carries the whole table's structure, and any racking here shows up as a wobble later.
Tools: Drill / Driver, Pocket Hole Jig. Materials: Pine, 1x3, 8 ft
Install the center support pieces to brace the long span of the apron and give the tabletop extra attachment points in the middle.
Tools: Drill / Driver. Materials: Turned table legs, 28-29" dining height, Leg mounting hardware
Mount the four turned legs to the apron corners using whatever hardware the leg manufacturer specifies — usually corner brackets or a threaded insert. Snug every leg evenly and check the table sits flat with no rock.
Tools: Drill / Driver, Random Orbit Sander
Center the finished apron assembly on the underside of the tabletop and screw up through the apron into the top, leaving an even overhang on all sides. Sand the whole table through the grits and finish as desired.