NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A one-drawer nightstand with hand-tapered legs joined by mitered trim, sized around a standard drawer slide.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Bottom | 4 | 3/4" × 3 1/2" × 18" | Pine | ☐ |
| Sides | 2 | 3/4" × 5 1/2" × 14" | Pine | ☐ |
| Back | 1 | 3/4" × 5 1/2" × 16 1/2" | Pine | ☐ |
| Legs Tapered per step 3 — mark 6" down one side, 1.5" in from the opposite edge at the bottom, and cut the connecting line. | 4 | 3/4" × 2 1/2" × 16" | Pine | ☐ |
| Front/back trim Both ends cut at 45°. | 2 | 3/4" × 2 1/2" × 12" | Pine | ☐ |
| Side trim Both ends cut at 45°. | 2 | 3/4" × 2 1/2" × 6 5/8" | Pine | ☐ |
| Drawer bottom | 1 | 3/4" × 11 1/4" × 15 1/2" | Pine | ☐ |
| Drawer sides | 2 | 3/4" × 3 1/2" × 11 1/4" | Pine | ☐ |
| Drawer back | 1 | 3/4" × 3 1/2" × 14" | Pine | ☐ |
| Top | 4 | 3/4" × 3 1/2" × 18" | Pine | ☐ |
| Drawer front Trimmed 1/4" narrower than the raw 1x6. | 1 | 3/4" × 5 1/4" × 16 1/4" | Pine | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| Pine, 1x3, 12 ft Legs and trim. | 1 each | ☐ |
| Pine, 1x4, 8 ft Bottom, top, and drawer sides/back. | 2 each | ☐ |
| Pine, 1x6, 6 ft Sides, back, and drawer front. | 1 each | ☐ |
| Pine, 1x12, 2 ft Drawer bottom — buy a 4 ft board if that's the shortest available. | 1 each | ☐ |
| Drawer slides, 10" or 11" | 1 pair | ☐ |
| Wood filler | 1 container | ☐ |
| Wood glue | 3 oz | ☐ |
| Wood screws, 1-1/4" and 2" | 1 box | ☐ |
| Finish nails | 1 box | ☐ |
Overall cost: $$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Drill / Driver, Pocket Hole Jig. Materials: Pine, 1x4, 8 ft, Pine, 1x6, 6 ft
Line up the four bottom boards side by side, flush to each other, and attach together (a pocket hole jig makes this fast). Attach a side board across each side of the bottom assembly, keeping the front, back, and sides flush.
Tools: Drill / Driver, Pocket Hole Jig. Materials: Pine, 1x6, 6 ft
Slip the back board between the two side boards, flush with the back edge, and attach through the sides into its ends.
Tools: Circular Saw. Materials: Pine, 1x3, 12 ft
Mark 6" down one edge of each leg. Along the bottom edge, measure 1-1/2" in from the opposite side. Draw a line connecting the two marks and cut along it on all four legs.
Tools: Brad Nailer, Miter Saw. Materials: Pine, 1x3, 12 ft, Wood glue
Cut each end of the front/back and side trim boards at a 45° angle, making sure the cuts are perpendicular to each other (not both leaning the same way). Use the trim pieces to connect the four tapered legs, keeping the top and inside edges flush and every taper pointing in toward the middle. Glue every joint and assemble with finishing nails or screws. Check for square by measuring corner to corner in both directions — matching measurements confirm it's square — before attaching this assembly to the nightstand body.
Tools: Drill / Driver, Pocket Hole Jig
Attach the leg assembly to the bottom of the nightstand body, set back 2-1/4" from the front and 1-1/2" from each side. Aim for at least one screw into each board.
Tools: Drill / Driver, Pocket Hole Jig. Materials: Pine, 1x4, 8 ft, Pine, 1x12, 2 ft
Attach a drawer side to each end of the drawer bottom, then attach the drawer back between the sides.
Follow the drawer-slide manufacturer's instructions to install the box — this is far easier before the top is on. These dimensions assume a 1/2" clearance allowance per side; if your slides use a different clearance, adjust the drawer box size to match. Keep the drawer box recessed 3/4" from the nightstand's face so the drawer front ends up flush later.
Tools: Brad Nailer, Pocket Hole Jig. Materials: Pine, 1x4, 8 ft, Wood glue
Once the drawer box is installed, attach the top — assemble the four boards side by side with a pocket hole jig, or attach them individually, using finish nails and glue.
Tools: Brad Nailer, Circular Saw. Materials: Pine, 1x6, 6 ft, Wood glue
Trim 1/4" off the drawer-front board so it's 5-1/4" tall — a table saw gives the cleanest cut, but a circular saw works. For a standard drawer pull, leave the front as a flat board. For a notched pull instead, cut a notch in the top edge with a reciprocating saw, measuring in 6" from each side and notching down 1". Center the finished drawer front on the drawer box with an even 1/8" gap all around (with the top in place, so the gap reads correctly), flush to the nightstand's face, and attach with finish nails and glue. Tracing the drawer box's outline onto the back of the front first helps you know exactly where to nail.