NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A three-board tabletop on a pocket-hole apron and four 2x2 legs — the whole build from one 1x8, one 2x2, and one 1x3, and a fair first project for a pocket-hole jig.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Tabletop boards If ripping from a 96"-long board, cut at 31-7/8" to account for saw-blade kerf across three cuts. | 3 | 3/4" × 7 1/2" × 32" | 1x8 | ☐ |
| Legs | 4 | 1 1/2" × 1 1/2" × 21 1/4" | 2x2 | ☐ |
| End aprons | 2 | 3/4" × 2 1/2" × 17 1/2" | 1x3 | ☐ |
| Side aprons If your 1x8s measure narrower than 7-1/2" actual width, take the difference, multiply by three, and subtract that from this length. | 2 | 3/4" × 2 1/2" × 27" | 1x3 | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 1x8, 8 ft The tabletop — measure the actual board width before finalizing the apron length. | 1 each | ☐ |
| 2x2, 8 ft The four legs. | 1 each | ☐ |
| 1x3, 8 ft End and side aprons. | 1 each | ☐ |
| Pocket hole screws, 1-1/4" | 30 each | ☐ |
| Wood glue | 2 oz | ☐ |
Overall cost: $. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Circular Saw, Pencil, Pocket Hole Jig, Tape Measure. Materials: 1x8, 8 ft, 1x3, 8 ft
Cut all boards per the cut list. Before you finalize the side aprons, measure your actual 1x8 boards — they don't always measure a true 7-1/2" wide. If yours are narrower, take the difference, multiply by three (three boards make the top), and subtract that number from the side apron length.
Drill pocket holes in all the joining ends — marking an X at each pocket-hole location as you cut keeps you from losing track of which end goes where.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 1x8, 8 ft, Pocket hole screws, 1-1/4", Wood glue
Join the three 1x8 boards edge to edge with pocket holes and glue. Solid wood here means the top can always be sanded and refinished later — a genuinely useful property for a surface that's about to meet crayons and markers.
Tools: Drill / Driver, Pocket Hole Jig, Speed Square. Materials: 2x2, 8 ft, 1x3, 8 ft, Pocket hole screws, 1-1/4", Wood glue
Drill all remaining pocket holes, then attach the legs to the aprons. Insetting the aprons slightly, or drilling the pocket holes on the outside faces, helps keep the legs from splitting. Check for square as you go.
Tools: Drill / Driver, Level, Pocket Hole Jig. Materials: Pocket hole screws, 1-1/4"
Line the tabletop up with the base and screw them together through the apron's pocket holes. Pocket holes are forgiving here — even if the tabletop isn't perfectly flat on its own, the screws pull it square against the base as they're driven.
Sand and finish, and let a kid loose on it.