NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A slim two-piece makeup vanity — a plank-top table with a small open hutch on the back for products. Sized around your own light-up mirror.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Base legs | 2 | 3/4" × 11 1/4" × 29 1/4" | 1x12 | ☐ |
| Base top | 1 | 3/4" × 11 1/4" × 53" | 1x12 | ☐ |
| Base aprons Cut to the measured distance between the legs at the tabletop. | 2 | 3/4" × 3 1/2" × 50 1/2" | 1x4 | ☐ |
| Hutch top | 1 | 3/4" × 7 1/4" × 53" | 1x8 | ☐ |
| Hutch verticals | 4 | 3/4" × 7 1/4" × 20 3/4" | 1x8 | ☐ |
| Hutch shelves | 2 | 3/4" × 7 1/4" × 11 3/4" | 1x8 | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 1x12, 10 ft (Pine) Base top and legs. | 1 each | ☐ |
| 1x4, 10 ft (Pine) Base aprons. | 1 each | ☐ |
| 1x8, 8 ft (Pine) Hutch shelves and sides. | 2 each | ☐ |
| Pocket hole screws, 1-1/4" | 1 box | ☐ |
| Brad nails, 1-1/4" | 1 box | ☐ |
| Wood glue | 5 oz | ☐ |
| Finish | 1 kit | ☐ |
| Light-up mirror Purchased. Size the hutch opening to fit it — not part of the woodworking. | 1 each | ☐ |
Overall cost: $$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Drill / Driver, Pocket Hole Jig, Speed Square. Materials: 1x12, 10 ft, Pocket hole screws, 1-1/4"
Drill three pocket holes on one end of each 1x12 leg board. Attach them to the underside of the top with 1-1/4" pocket screws, leaving a 1/2" overhang on each end. Keep the legs square to the top.
Tools: Drill / Driver, Pocket Hole Jig, Tape Measure. Materials: 1x4, 10 ft, Pocket hole screws, 1-1/4"
Measure the distance between the two legs at the tabletop for the most accurate number, and cut the two 1x4 aprons to it. Drill two 3/4" pocket holes at each end, plus pocket holes along one edge of the top apron facing up to attach it to the tabletop. Fasten with 1-1/4" pocket screws. This ties the legs together and stiffens the base.
Tools: Brad Nailer, Drill / Driver, Random Orbit Sander. Materials: 1x8, 8 ft, Brad nails, 1-1/4", Wood glue, Finish
Build the hutch with brad nails and glue — it isn't structural, so nails are fine and hide better than pocket screws. Build the two shelf sections first, then add the top. Size the center opening to your light-up mirror. Connect the finished hutch to the base with a few screws through the back.
Sand and finish the whole piece.