Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.

Simple Playhouse — Back Wall Panel

The framed, sheathed, and trimmed back wall of a kids' playhouse. Basic stud-wall framing at a small, forgiving scale.

Cut list

Part	Qty	T × W × L	Material	✓
Top and bottom plates	2	1 1/2" × 1 1/2" × 90"	2x2	☐
Wall studs	7	1 1/2" × 1 1/2" × 45"	2x2	☐
Back panel Trim 6" off a full 96" sheet to get 90" — keeps the wall under 96" to fit a standard 8-ft deck.	1	1/4" × 48" × 90"	1/4" plywood	☐
Top and bottom trim	2	3/4" × 2 1/2" × 90"	1x3	☐
Side trim	2	3/4" × 1 1/2" × 43"	1x2	☐

Item	Qty	✓
1/4" plywood Back panel sheathing. Use an exterior-rated sheet — this wall lives outside.	1 sheet	☐
2x2 furring strips, 8 ft (SPF / Pine) Plates and studs.	6 each	☐
1x3 furring strips, 8 ft (Pine) Top and bottom trim.	2 each	☐
1x2 furring strip, 8 ft (Pine) Side trim.	1 each	☐
Self-tapping screws, 2-1/2"	1 box	☐
Screws, 3" For joining this wall to the gable end wall at assembly.	1 box	☐
Nails, 1-1/4"	1 box	☐
Wood glue (waterproof) Exterior build — use a waterproof (Type II or III) glue.	8 oz	☐
Exterior finish / primer and paint	1 kit	☐

Overall cost: $$. Lumber varies by region, species, and season, so we give a band rather than a figure.

Brad Nailer
Sheathing and trim are glued and nailed.
Circular Saw
For trimming the plywood sheet to 90" and cutting the furring strips.
Drill / Driver
Predrill the plates and drive the framing screws.
Pencil
Safety Glasses
Speed Square
Your square is how you keep the wall true — check after every stud.
Tape Measure
Hammer — optional
Hearing Protection — optional
Random Orbit Sander — optional

1. Frame the wall
Tools: Drill / Driver, Pencil, Speed Square, Tape Measure. Materials: 2x2 furring strips, 8 ft, Self-tapping screws, 2-1/2"
Mark both the top and bottom plates where each stud lands, then predrill all the holes in the plates. Fasten the seven studs to the plates, working across the wall.
Check for square once all the studs are fastened — measure both diagonals and adjust until they match. A wall framed out of square makes every later step harder and won't mate cleanly with the rest of the playhouse.
2. Sheath the wall
Tools: Brad Nailer, Circular Saw, Tape Measure. Materials: 1/4" plywood, Nails, 1-1/4", Wood glue (waterproof)
Take a full sheet of 1/4" plywood and trim 6" off the end to get a 90" x 48" panel. The 6" comes off so the overall wall stays under 96" and drops onto a standard 8-ft deck platform without extra cutting.
Glue and fasten the panel to the frame with 1-1/4" nails, keeping the edges flush to the plates and outer studs.
3. Add the trim
Tools: Brad Nailer, Circular Saw. Materials: 1x3 furring strips, 8 ft, 1x2 furring strip, 8 ft, Nails, 1-1/4", Wood glue (waterproof)
Cut the longer top and bottom 1x3 trim first and glue and nail it down with 1-1/4" nails. Then add the 1x2 side trim at the ends, keeping the outside edges flush.
4. Assemble into the playhouse