NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
An open-shelf nightstand with a single drawer, built from 1-by boards and a brad nailer. A clean first-drawer project.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Shelves Part A. | 2 | 3/4" × 11 1/4" × 15" | 1x12 | ☐ |
| Leg side pieces Part B — the side face of each leg. | 4 | 3/4" × 1 1/2" × 25 1/2" | 1x2 | ☐ |
| Leg front/back pieces Part C — the front/back face of each leg. | 4 | 3/4" × 2 1/2" × 25 1/2" | 1x3 | ☐ |
| Drawer box sides Part D. If using a 1x12 instead, make the plywood back (E) 1/2" shorter. | 2 | 1/2" × 5 3/4" × 11 1/2" | 1/2" plywood | ☐ |
| Drawer box back Part E. | 1 | 1/2" × 5 3/4" × 14" | 1/2" plywood | ☐ |
| Drawer guides Part F. | 2 | 3/4" × 1 1/2" × 11" | 1x2 | ☐ |
| Bottom front trim Part G. | 1 | 3/4" × 1 1/2" × 11 1/2" | 1x2 | ☐ |
| Side trim pieces Part H. | 4 | 3/4" × 1 1/2" × 8 1/2" | 1x2 | ☐ |
| Back countertop piece Part I. | 1 | 3/4" × 2 1/2" × 18 1/2" | 1x3 | ☐ |
| Front countertop piece Part J. | 1 | 3/4" × 11 1/4" × 18 1/2" | 1x12 | ☐ |
| Drawer bottom Part K. | 1 | 3/4" × 9 1/4" × 9 1/2" | 1x10 | ☐ |
| Drawer back Part L. | 1 | 3/4" × 5 1/2" × 9 1/2" | 1x6 | ☐ |
| Drawer sides Part M. | 2 | 3/4" × 5 1/2" × 10 1/4" | 1x6 | ☐ |
| Drawer face Part N. | 1 | 3/4" × 5 1/2" × 11" | 1x6 | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 1x12, 8 ft (Pine) Shelves and the front countertop piece. | 1 each | ☐ |
| 1x2, 8 ft (Pine) Leg pieces, drawer guides, and trim. | 2 each | ☐ |
| 1x3, 8 ft (Pine) Front/back leg pieces and the back countertop piece. | 1 each | ☐ |
| 1x6, 8 ft (Pine) Drawer back, sides, and face. | 1 each | ☐ |
| 1x10, 4 ft (Pine) Drawer bottom. | 1 each | ☐ |
| 1/2" plywood Drawer box sides and back — a scrap/partial sheet is plenty. A 1x12 can substitute for the sides. | 1 sheet | ☐ |
| Wood glue | 6 oz | ☐ |
| Brad nails, 1-1/4" | 1 box | ☐ |
| Wood filler and finish | 1 kit | ☐ |
| Drawer knob | 1 each | ☐ |
Overall cost: $$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Brad Nailer, Speed Square, Tape Measure. Materials: 1x2, 8 ft, 1x3, 8 ft, Wood glue, Brad nails, 1-1/4"
Each leg is a 1x2 glued and nailed to a 1x3 along the long edge to form an L. Make all four.
The orientation is the single most important thing in this build: the 1x3 face goes on the front and back of the nightstand, the 1x2 face on the sides. Mark each leg 3-1/2" up from the bottom while you're at it — that mark sets the shelf height. Get the leg orientation wrong and the drawer will not fit.
Tools: Brad Nailer, Tape Measure. Materials: 1x12, 8 ft, Wood glue, Brad nails, 1-1/4"
Fasten the legs to one shelf so the bottom of the shelf sits flush with the 3-1/2" marks from the previous step. That leaves a 3-1/2" clearance under the nightstand. Keep the 1x3 faces front and back.
Tools: Brad Nailer, Tape Measure. Materials: 1x12, 8 ft, Wood glue, Brad nails, 1-1/4"
Mark the legs 5-3/4" down from the top on the inside faces, and attach the top shelf there. That 5-3/4" clearance from the top of the shelf to the top of the piece is the drawer box's home.
Tools: Brad Nailer. Materials: 1/2" plywood, Wood glue, Brad nails, 1-1/4"
With the case standing, add the plywood side pieces of the drawer box. If you chose to use 1x12 for the sides instead of plywood, remember to make the back piece (E) 1/2" shorter — 13-1/2" x 5-3/4".
Nail the front trim piece (G) along the bottom edge, keeping its top edge flush with the shelf. Then add the four side trim pieces (H) to the bottom shelf and the bottom of the drawer-box sides.
Tools: Brad Nailer, Tape Measure. Materials: 1x12, 8 ft, 1x3, 8 ft, Wood glue, Brad nails, 1-1/4"
Add the back countertop piece (I) with a 1" overhang on each side, then the front countertop piece (J) with a 1" overhang on the sides and front.
Before you build the drawer, measure the inside of the drawer box: it should be exactly 11" wide and about 11" deep (10-1/4" to the bottom shelf, 11" to the side of the legs). Fix any discrepancy now — the drawer is built to these numbers.
Tools: Brad Nailer, Speed Square. Materials: 1x6, 8 ft, 1x10, 4 ft, Wood glue, Brad nails, 1-1/4"
Start with the bottom piece (K) and nail the back (L) to it, driving through the back into the bottom. Add a side, nailing through the side into both the bottom and the back; repeat on the other side. Finally nail the face (N) on.
Work on a flat surface and keep everything square as you go — a drawer racked out of square binds in a wood-guided opening.
Tools: Drill / Driver. Materials: Wood filler and finish, Drawer knob
If everything was measured honestly, the drawer slides into the opening on its guides with a clean fit. If it binds, find the tight spot rather than forcing it.
Fill nail holes with wood filler, sand smooth, and finish as you like. Add the knob last.