NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A long, low media console with three 1x12 open shelves framed in 2x2 and 1x2 trim — a wide, low-profile stand sized for a TV rather than a general living-room console.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Top front/back trim | 2 | 1 1/2" × 1 1/2" × 60" | 2x2, 8 ft | ☐ |
| Top side trim | 2 | 1 1/2" × 1 1/2" × 11 1/4" | 2x2, 8 ft | ☐ |
| Shelves and top | 3 | 3/4" × 11 1/4" × 57" | 1x12, 15 ft total (mixed lengths) | ☐ |
| Legs | 4 | 1 1/2" × 2 1/2" × 27" | 2x3, 8 ft or stud length | ☐ |
| Shelf side trim | 4 | 3/4" × 1 1/2" × 11 1/4" | 1x2, 6 ft | ☐ |
| Shelf front/back trim | 4 | 3/4" × 1 1/2" × 55" | 1x2, 6 ft | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 2x2, 8 ft | 2 each | ☐ |
| 1x12, 15 ft total (mixed lengths) | 15 ft | ☐ |
| 2x3, 8 ft or stud length | 2 each | ☐ |
| 1x2, 6 ft | 4 each | ☐ |
| Pocket hole screws, 1-1/4" and 2-1/2" | 100 each | ☐ |
| Wood glue | 4 oz | ☐ |
| Primer and paint, or stain and poly | 1 set | ☐ |
Overall cost: $$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 2x2, 8 ft, 1x12, 15 ft total (mixed lengths), Pocket hole screws, 1-1/4" and 2-1/2", Wood glue
Drill 3/4" pocket holes around all four sides of the top shelf board. Drill a single 1-1/2" pocket hole on each end of the 11-1/4" side trim pieces. Attach the side trim with 1-1/4" pocket hole screws and glue, then attach the front and back trim with 1-1/4" pocket hole screws (into the top) and 2-1/2" pocket hole screws (at the corners into the side trim).
Tools: Drill / Driver, Pocket Hole Jig. Materials: 2x3, 8 ft or stud length, Pocket hole screws, 1-1/4" and 2-1/2", Wood glue
Drill two 1-1/2" pocket holes on one end of each leg. Attach to the underside of the top with glue and 2-1/2" pocket hole screws.
Tools: Drill / Driver, Pocket Hole Jig, Tape Measure. Materials: 1x2, 6 ft, Pocket hole screws, 1-1/4" and 2-1/2", Wood glue
Inset the side trim 3/4" from the outside of the legs, using a scrap piece of 1x wood as a spacer if helpful. Drill a 3/4" pocket hole on each end of the side trim and attach to the legs with 1-1/4" pocket hole screws and glue.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 1x12, 15 ft total (mixed lengths), Pocket hole screws, 1-1/4" and 2-1/2", Wood glue
Drill 3/4" pocket holes around all four edges of the shelves, including into the legs. Attach to the side trim and legs with 1-1/4" pocket hole screws and glue.
Tools: Random Orbit Sander. Materials: Primer and paint, or stain and poly
Sand all surfaces and apply primer and paint, or stain and poly.