NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
One oak board, five turned or bought pegs, mounted into studs. Ninety minutes, and it holds a winter's worth of coats.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Backboard 32" spans two studs at 16" on center, with a little overhang. This length is chosen by the studs, not by taste. | 1 | 3/4" × 5" × 32" | White Oak | ☐ |
| Pegs Tenon on the back end, sized to your drill bit — usually 1/2". | 5 | 5/8" × 5/8" × 3 1/2" | Maple or Oak | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| White oak, 4/4, 5" wide (White Oak) One nice, straight board. Quartersawn white oak shows ray fleck and looks spectacular for the money. | 1.5 board feet | ☐ |
| Shaker pegs, 3-1/2" Buy them or turn them. Bought pegs are cheap and perfectly good. | 5 each | ☐ |
| Wood glue | 1 oz | ☐ |
| Wood screws, #10 x 3" 3" so they bite deep into the stud, through the drywall and the board. | 3 each | ☐ |
| Wood plugs or buttons Cover the mounting screws. Turns a hardware-store look into a finished piece. | 3 each | ☐ |
| Clear interior finish (hardwax oil or wipe-on poly) | 4 oz | ☐ |
Overall cost: $. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Combination Square, Tape Measure
Locate your studs first. Standard spacing is 16" on center.
Your board's length is decided by where the studs are — you want to hit at least two of them, ideally three. A 32" board spanning two studs with overhang is the usual answer.
Designing the board first and hoping studs turn up where you need them is exactly how coat racks end up on drywall anchors.
Tools: Random Orbit Sander, Table Saw. Materials: White oak, 4/4, 5" wide
Flatten, thickness to 3/4", rip to 5" wide, crosscut to length.
If you bought a surfaced board and it's flat, you can skip straight to sanding. There's no shame in that here.
Tools: Drill / Driver, Drill Press. Materials: Shaker pegs, 3-1/2"
Mark five evenly spaced hole positions along the centerline. Bore holes matching your pegs' tenons — usually 1/2" — about 5/8" deep.
Perpendicular matters. Drill press if you have one; if not, clamp a scrap block with a squared hole as a guide. A peg leaning 5° off square is instantly visible and looks like a mistake, because it is one.
Tools: Router
Chamfer or round over the front edges and the ends. Even a small 1/8" chamfer takes the board from 'plank' to 'made'.
Optional: a gentle curve along the top edge. Nice touch, five extra minutes.
Tools: Drill / Driver. Materials: Wood screws, #10 x 3", Wood plugs or buttons
Drill three mounting holes on the board's centerline, positioned to land on your studs.
Counterbore each one so the screw head sits below the surface and a wood plug can cover it. This is the detail that hides the hardware and makes it look intentional.
Tools: Lathe, Random Orbit Sander. Materials: Shaker pegs, 3-1/2", Wood glue, Clear interior finish (hardwax oil or wipe-on poly)
Glue the pegs in. Sand to 220.
White oak takes hardwax oil beautifully — the ray fleck in quartersawn stock lights up. Two or three coats.
Finish before mounting. You cannot finish the back of a board that's already on the wall.
Tools: Drill / Driver. Materials: Wood screws, #10 x 3", Wood plugs or buttons
Level the board on the wall, drill pilot holes through the counterbores, and drive 3" screws into the studs.
Glue the plugs in over the screw heads, pare them flush when dry, touch up the finish.
Then hang a heavy winter coat on the end peg and lean on it. It shouldn't budge. If it does, you missed a stud — take it down and fix it now, not after it rips out of the wall.