NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A long, low console with a plywood-lined firewood tray built into a 2x4 frame, angled front legs, and a full plywood back panel — genuine firewood storage furniture, not a shelf repurposed for logs.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Frame long rails | 4 | 1 1/2" × 3 1/2" × 66 1/2" | 2x4, 8 ft | ☐ |
| Frame short rails | 4 | 1 1/2" × 3 1/2" × 17" | 2x4, 8 ft | ☐ |
| Bottom tray liner | 1 | 3/8" × 16 1/2" × 69 1/2" | 3/8" plywood, full sheet | ☐ |
| Front legs | 4 | 3/4" × 3 1/2" × 31 3/4" | 1x4, 8 ft | ☐ |
| Back legs | 2 | 3/4" × 3 1/2" × 31 3/4" | 1x4, 8 ft | ☐ |
| Back panel | 1 | 3/8" × 31 1/2" × 71" | 3/8" plywood, full sheet | ☐ |
| Top edge trim | 1 | 3/4" × 7 1/4" × 71" | 1x8, 6 ft | ☐ |
| Top board | 1 | 3/4" × 11 1/4" × 71" | 1x12, 6 ft | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 3/8" plywood, full sheet | 1 each | ☐ |
| 1x4, 8 ft | 2 each | ☐ |
| 2x4, 8 ft | 4 each | ☐ |
| 1x8, 6 ft | 1 each | ☐ |
| 1x12, 6 ft | 1 each | ☐ |
| Self-tapping wood screws, 3" | 30 each | ☐ |
| Brad nails, 1-1/4" and 3/4" | 80 each | ☐ |
| Wood glue | 4 oz | ☐ |
| Paint or stain | 1 set | ☐ |
Overall cost: $$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Drill / Driver. Materials: 2x4, 8 ft, Self-tapping wood screws, 3"
Build two frames out of the 2x4 long and short rails using 3" screws, two per joint.
Tools: Brad Nailer. Materials: 3/8" plywood, full sheet, Brad nails, 1-1/4" and 3/4", Wood glue
Attach the plywood tray liner to the bottom frame with 3/4" brad nails and wood glue.
Tools: Brad Nailer. Materials: 1x4, 8 ft, Brad nails, 1-1/4" and 3/4", Wood glue
Attach the front legs to the front of both trays with 1-1/4" brad nails and glue, keeping outside edges flush. Add the single back legs the same way.
Tools: Brad Nailer. Materials: 3/8" plywood, full sheet, Brad nails, 1-1/4" and 3/4", Wood glue
Attach the plywood back panel to the project with 3/4" brad nails and glue.
Tools: Brad Nailer. Materials: 1x8, 6 ft, 1x12, 6 ft, Brad nails, 1-1/4" and 3/4", Wood glue
Attach the top board and edge trim with 1-1/4" brad nails and glue. Add supports or hidden storage to the top if desired.
Tools: Random Orbit Sander. Materials: Paint or stain
Sand all surfaces and apply paint or stain.