NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A tall entryway piece combining a storage cubby bench below with a jigsaw-shaped hook rail above — a genuine bench-plus-hooks hall tree distinct from this catalog's simpler entryway benches.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Bench top | 1 | 3/4" × 15 3/4" × 49 1/2" | 3/4" plywood, ripped to 15-3/4" strips, full sheet | ☐ |
| Bench bottom | 1 | 3/4" × 15 3/4" × 46 1/2" | 3/4" plywood, ripped to 15-3/4" strips, full sheet | ☐ |
| Cubby dividers | 2 | 3/4" × 15 3/4" × 14" | 3/4" plywood, ripped to 15-3/4" strips, full sheet | ☐ |
| Bench end panels | 2 | 3/4" × 15 3/4" × 17 1/4" | 3/4" plywood, ripped to 15-3/4" strips, full sheet | ☐ |
| Bottom support rails | 2 | 3/4" × 2 1/2" × 46 1/2" | 1x3, 8 ft | ☐ |
| Face frame top rail | 1 | 3/4" × 1 1/2" × 49 1/2" | 1x2, 8 ft | ☐ |
| Face frame front rail | 1 | 3/4" × 1 1/2" × 48" | 1x2, 8 ft | ☐ |
| Face frame stiles | 2 | 3/4" × 1 1/2" × 15 3/4" | 1x2, 8 ft | ☐ |
| Face frame mid rail | 1 | 3/4" × 2 1/2" × 45" | 1x3, 8 ft | ☐ |
| Hook panel back frame sides | 2 | 3/4" × 3 1/2" × 56" | 1x4, 8 ft | ☐ |
| Hook panel back frame rails | 2 | 3/4" × 2 1/2" × 47" | 1x3, 8 ft | ☐ |
| Hook panel back frame mid rails | 6 | 3/4" × 2 1/2" × 12" | 1x3, 8 ft | ☐ |
| Hook rail top trim | 1 | 3/4" × 3 1/2" × 41" | 1x4, 8 ft | ☐ |
| Hook rail top cap | 1 | 3/4" × 5 1/2" × 41" | 1x6, 4 ft | ☐ |
| Hook panel shaped sides Shaped with a jigsaw; clamp together and sand to match. | 2 | 3/4" × 11 1/4" × 24" | 1x12, 4 ft | ☐ |
| Back panel (3 sections) Split into three boards for transport; combined width covers 48". | 3 | 1/2" × 16" × 74" | 1/2" plywood, full sheet | ☐ |
| Base moulding Cut to fit around the bench base. | 1 | 3/4" × 2 1/4" × 96" | Base moulding, 2-1/4 in, 8 ft | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 3/4" plywood, ripped to 15-3/4" strips, full sheet | 1 each | ☐ |
| 1x4, 8 ft | 2 each | ☐ |
| 1x2, 8 ft | 2 each | ☐ |
| 1x3, 8 ft | 3 each | ☐ |
| 1x6, 4 ft | 1 each | ☐ |
| 1x12, 4 ft | 1 each | ☐ |
| 1/2" plywood, full sheet | 1 each | ☐ |
| Base moulding, 2-1/4 in, 8 ft | 1 each | ☐ |
| Pocket hole screws, 1-1/4" | 100 each | ☐ |
| Finish nails, 1-1/4" | 100 each | ☐ |
| Wood glue | 6 oz | ☐ |
| Coat hooks | 5 each | ☐ |
| Primer and paint, or stain and poly | 1 set | ☐ |
Overall cost: $$$$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 3/4" plywood, ripped to 15-3/4" strips, full sheet, Pocket hole screws, 1-1/4"
Build the bench box from the ripped plywood pieces (top, bottom, dividers, end panels), following the cubby layout, using 3/4" pocket holes and 1-1/4" pocket hole screws.
Tools: Drill / Driver. Materials: 1x3, 8 ft, Pocket hole screws, 1-1/4"
Attach the bottom support rails under the bench so a sitter's weight transfers directly to the floor.
Tools: Brad Nailer, Drill / Driver, Pocket Hole Jig. Materials: 1x2, 8 ft, 1x3, 8 ft, Pocket hole screws, 1-1/4", Finish nails, 1-1/4", Wood glue
Build the face frame with 3/4" pocket holes and 1-1/4" pocket hole screws, and attach to the bench box with 1-1/4" finish nails and glue.
Tools: Brad Nailer. Materials: Base moulding, 2-1/4 in, 8 ft, Finish nails, 1-1/4"
Wrap the base moulding around the bottom of the bench section, mitering corners as needed.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 1x4, 8 ft, 1x3, 8 ft, Pocket hole screws, 1-1/4"
Build the vertical back frame for the hook panel from the 1x4 sides and 1x3 rails with pocket holes, attaching it above the bench section.
Tools: Brad Nailer. Materials: 1x4, 8 ft, 1x6, 4 ft, Finish nails, 1-1/4", Wood glue
Attach the top trim and top cap across the top of the hook panel frame.
Tools: Brad Nailer, Jigsaw, Random Orbit Sander. Materials: 1x12, 4 ft, Finish nails, 1-1/4", Wood glue
Mark the shaped profile on the 1x12 hook panel side pieces and cut out with a jigsaw. Clamp the two pieces together and sand until they match exactly. Attach in place.
Tools: Brad Nailer, Drill / Driver, Random Orbit Sander. Materials: 1/2" plywood, full sheet, Finish nails, 1-1/4", Coat hooks, Primer and paint, or stain and poly
Attach the three back panel sections, then attach coat hooks. Sand all surfaces and apply primer and paint, or stain and poly.