NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A chunky 1x12 console that doubles as a desk — the front panels flip down on Euro hinges to become a keyboard tray and to open leg storage. Clever, hidden-hardware build.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Outer legs | 2 | 3/4" × 11 1/4" × 29 1/4" | 1x12 | ☐ |
| Shelf | 1 | 3/4" × 11 1/4" × 46 1/2" | 1x12 | ☐ |
| Inner legs | 2 | 3/4" × 11 1/4" × 24 1/2" | 1x12 | ☐ |
| Top | 1 | 3/4" × 11 1/4" × 48" | 1x12 | ☐ |
| Dividers Doubles as a shelf-height spacer during assembly. | 6 | 3/4" × 11 1/4" × 4" | 1x12 | ☐ |
| Keyboard fold-down | 1 | 3/4" × 5 1/2" × 48" | 1x6 | ☐ |
| Storage leg doors | 2 | 3/4" × 5 1/2" × 23 3/4" | 1x6 | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 1x12, 8 ft Top and shelf. | 1 each | ☐ |
| 1x12, 10 ft Legs and dividers. | 1 each | ☐ |
| 1x6, 8 ft Keyboard fold-down and leg storage doors. | 1 each | ☐ |
| Frameless full-overlay Euro hinges | 6 each | ☐ |
| Brad nails, 1-1/4 in and 2 in | 1 box | ☐ |
| Self-tapping screws, 2 in | 1 box | ☐ |
| Wood glue | 1 bottle | ☐ |
| Finish or paint | 1 quart | ☐ |
Overall cost: $$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Brad Nailer, Circular Saw, Drill / Driver, Pocket Hole Jig. Materials: 1x12, 8 ft, 1x12, 10 ft, Self-tapping screws, 2 in, Wood glue
Attach the legs to the desk shelf with your choice of fastener — brad nails and glue, 2" screws, or pocket holes, in any combination. Pocket holes make the strongest joint here and are recommended. Tip: use one of the 4" divider pieces as a temporary spacer to set your shelf height consistently.
Tools: Drill / Driver. Materials: Frameless full-overlay Euro hinges
Install the six Euro hinges at this stage — it's much harder to get a drill inside the project as it closes in. Screw them to the project with the flat front flush to the front edges; a scrap block helps hold them flush. Exact placement isn't critical, just close to the diagram.
Tools: Brad Nailer, Drill / Driver, Pocket Hole Jig. Materials: 1x12, 8 ft, 1x12, 10 ft, Brad nails, 1-1/4 in and 2 in, Wood glue
Attach the inner leg pieces to the shelf — pocket holes recommended for strength. Then attach the top to the outer legs; 1-1/4" brad nails with glue are ideal here since they're the easiest to hide on a visible top surface.
Tools: Brad Nailer. Materials: 1x12, 10 ft, Brad nails, 1-1/4 in and 2 in, Wood glue
Attach the dividers inside the project with 1-1/4" brads and glue. They're spaced to fit an 8-1/2" x 11" book or paper in each opening, but they're not structural — move them wherever suits what you'll store without weakening anything.
Position the 1x6 fold-down faces under the project — the center one is the keyboard tray, the two leg panels are storage doors — and attach them through the hinges with screws. They should swing down cleanly and sit flush when closed.
Tools: Brad Nailer, Random Orbit Sander. Materials: 1x6, 8 ft, Brad nails, 1-1/4 in and 2 in, Wood glue, Finish or paint
If the piece needs more support, enclose the back with 1x6 boards (attached with 1-1/4" brads and glue) to add rigidity. The keyboard fold-down can be further strengthened with a hidden chain or hinge support on the insides of the dividers, which stops it from swinging too far.
Sand and finish or paint.