NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A plywood cabinet with a scrolled footer and full-overlay doors, sized for a TV or bins of toys behind closed doors instead of open shelves.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Sides Shortened 1" from the original diagram to fit efficiently on a single sheet — does not change shelf placement. | 2 | 3/4" × 21 3/4" × 59" | 3/4" plywood | ☐ |
| Top | 1 | 3/4" × 21 3/4" × 42" | 3/4" plywood | ☐ |
| Bottom shelf | 1 | 3/4" × 21 3/4" × 36 1/2" | 3/4" plywood | ☐ |
| Additional shelf (optional) | 1 | 3/4" × 21 3/4" × 36 1/2" | 3/4" plywood | ☐ |
| Side frame verticals Shortened 1" to match the sides. | 4 | 3/4" × 2 1/2" × 59" | 1x3 | ☐ |
| Side frame horizontals, long | 4 | 3/4" × 3 1/2" × 18 1/4" | 1x4 | ☐ |
| Side frame horizontals, short | 2 | 3/4" × 2 1/2" × 18 1/4" | 1x3 | ☐ |
| Back panel Shortened 1" to match the sides. | 1 | 1/4" × 59 3/4" × 38 1/2" | 1/4" plywood | ☐ |
| Top/bottom supports | 2 | 1 1/2" × 1 1/2" × 38" | 2x2 | ☐ |
| Top front trim | 1 | 3/4" × 2 1/2" × 42" | 1x3 | ☐ |
| Footer front, mitered Long point to long point, both ends cut at a 45° bevel, NOT parallel. | 1 | 3/4" × 3 1/2" × 41" | 1x4 | ☐ |
| Footer sides, mitered Long point measurement, one end cut at 45° bevel. | 2 | 3/4" × 3 1/2" × 24" | 1x4 | ☐ |
| Footer top trim front Long point to long point, both ends cut at 45°, NOT parallel. | 1 | 3/4" × 1 1/2" × 42 1/2" | 1x2 | ☐ |
| Footer top trim sides Long point measurement, one end cut at 45°. | 2 | 3/4" × 1 1/2" × 24 3/4" | 1x2 | ☐ |
| Door frame stiles Shortened 1" to match cabinet height. | 4 | 3/4" × 2 1/2" × 52 1/4" | 1x3 | ☐ |
| Door frame rails Trim to fit — 1x3 widths vary; overall door width should be roughly 18-3/4" or half the opening minus 1/4". | 6 | 3/4" × 2 1/2" × 13 3/4" | 1x3 | ☐ |
| Door back panels | 2 | 1/4" × 18 3/4" × 52 1/4" | 1/4" plywood | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 3/4" plywood, 4x8 sheet Rip into 21-3/4"-wide strips for the sides, top, and shelves. | 2 each | ☐ |
| 1/4" plywood, 4x8 sheet Cabinet back and both door back panels. | 2 each | ☐ |
| 1x3 board, 8 ft (Pine) | 8 each | ☐ |
| 1x4 board, 8 ft (Pine) | 2 each | ☐ |
| 2x2 board, 8 ft (Pine) | 1 each | ☐ |
| 1x2 board, 8 ft (Pine) | 1 each | ☐ |
| Pocket-hole screws, 1-1/4" and 1-1/2" | 120 each | ☐ |
| Finish nails, 1-1/4" and 2" | 80 each | ☐ |
| Cabinet door hinges | 6 each | ☐ |
| Magnetic door clasps | 2 each | ☐ |
| Door knobs | 2 each | ☐ |
Overall cost: $$$. Lumber varies by region, species, and season, so we give a band rather than a figure.