NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A rolling router table that's a real shop cabinet underneath — bit-storage drawers, two deep drawers on slides, a face frame, and casters. The drawer prep order is the whole trick.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Carcass horizontals Bottom, mid shelf, and top. | 3 | 3/4" × 19" × 26 1/2" | 3/4" plywood | ☐ |
| Drawer bay dividers | 2 | 3/4" × 19" × 8 1/4" | 3/4" plywood | ☐ |
| Carcass sides | 2 | 3/4" × 19" × 28 1/2" | 3/4" plywood | ☐ |
| Top cleats Or the width of your plywood if you went 18". | 5 | 3/4" × 2 1/2" × 19" | 1x3 | ☐ |
| Face frame stiles | 2 | 3/4" × 1 1/2" × 28 1/2" | 1x2 | ☐ |
| Face frame rails | 4 | 3/4" × 1 1/2" × 25" | 1x2 | ☐ |
| Face frame drawer dividers | 2 | 3/4" × 1 1/2" × 7 1/2" | 1x2 | ☐ |
| Small drawer sides | 2 | 3/4" × 5 1/2" × 16" | 1x6 | ☐ |
| Small drawer front/back | 2 | 3/4" × 5 1/2" × 5" | 1x6 | ☐ |
| Bit holder block Drilled 1/4" and 1/2" holes hold router bits upright by their shanks. | 1 | 3/4" × 5 1/2" × 14 1/2" | 1x6 | ☐ |
| Small drawer faces | 2 | 3/4" × 7 1/4" × 5 1/2" | 1x8 | ☐ |
| Large drawer sides | 4 | 3/4" × 5 1/2" × 22 1/2" | 1x6 | ☐ |
| Large drawer fronts/backs | 4 | 3/4" × 5 1/2" × 16" | 1x6 | ☐ |
| Large drawer bottoms | 2 | 1/4" × 16" × 24" | 1/4" plywood | ☐ |
| Large drawer faces | 2 | 3/4" × 7 1/4" × 24 3/4" | 1x8 | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| Plywood, 3/4", 4x8 sheet Ripped into two 19" x 8-ft strips. The leftover strip can replace some 1x6 — the source suggests an 18" cabinet depth to get two 5-1/2" strips from scrap. | 1 each | ☐ |
| Plywood, 1/4", 2x4 project panel Large drawer bottoms. | 1 each | ☐ |
| 1x6, 8 ft Drawer boxes. Skip if using the plywood scrap. | 3 each | ☐ |
| 1x3, 8 ft Top cleats and drawer-bay framing. | 1 each | ☐ |
| 1x2, 8 ft Face frame. | 2 each | ☐ |
| 1x8, 6 ft Drawer faces. | 1 each | ☐ |
| Drawer slides, side mount, pair One small pair for the bit drawer, two for the large drawers. | 3 each | ☐ |
| Casters At least two locking. A router table that creeps mid-cut is a hazard, not a convenience. | 4 each | ☐ |
| Pocket hole screws, 1-1/4" | 100 each | ☐ |
| Finish nails, 1-1/4" | 100 each | ☐ |
| Wood glue | 8 oz | ☐ |
Overall cost: $$$. Lumber varies by region, species, and season, so we give a band rather than a figure.