NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A tall two-door armoire in hardwood plywood with hobby-board door detailing, crown and base moulding, and optional drawers — a real furniture-grade wardrobe.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Sides | 2 | 3/4" × 23 1/4" × 66" | 3/4" plywood | ☐ |
| Shelves | 4 | 3/4" × 23 1/4" × 38 1/2" | 3/4" plywood | ☐ |
| Drawer divider | 1 | 3/4" × 23 1/4" × 6 1/2" | 3/4" plywood | ☐ |
| Header trim Cut to fit. | 1 | 3/4" × 3 1/2" × 40" | 1x4 | ☐ |
| Bottom side trim | 2 | 3/4" × 2 1/2" × 26 1/2" | 1x3 | ☐ |
| Top side trim For flat-folding doors. | 2 | 3/4" × 2 1/2" × 36" | 1x3 | ☐ |
| Shelf trim | 2 | 3/4" × 1 1/2" × 35" | 1x2 | ☐ |
| Side crown trim | 4 | 3/4" × 1 1/2" × 24 1/4" | 1x2 | ☐ |
| Bottom front crown trim | 1 | 3/4" × 1 1/2" × 41 1/2" | 1x2 | ☐ |
| Top crown front trim | 1 | 3/4" × 1 1/2" × 43" | 1x2 | ☐ |
| Base moulding sides Mitered out on front end; measure to fit. | 2 | 1/2" × 5 1/4" × 25" | Base moulding | ☐ |
| Base moulding front Mitered out both ends. | 1 | 1/2" × 5 1/4" × 41 1/2" | Base moulding | ☐ |
| Top door backs | 2 | 1/2" × 17 1/4" × 35 3/4" | 1/2" plywood | ☐ |
| Bottom door backs | 2 | 1/2" × 17 1/4" × 19 1/2" | 1/2" plywood | ☐ |
| Door top/bottom trim | 8 | 1/4" × 2 1/2" × 17 1/4" | Hobby board | ☐ |
| Top door side trim Cut to measurement. | 4 | 1/4" × 2 1/2" × 30 3/4" | Hobby board | ☐ |
| Bottom door side trim | 4 | 1/4" × 2 1/2" × 14 1/2" | Hobby board | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 3/4" hardwood plywood, 4x8 sheet Carcass sides and shelves. | 2 each | ☐ |
| 1/4" plywood, 4x8 sheet Back. | 1 each | ☐ |
| 1/2" hardwood plywood, half sheet Door backs. | 1 each | ☐ |
| 1x4 board, 4 ft (Hardwood) | 1 each | ☐ |
| 1x3 board, 8 ft (Hardwood) | 2 each | ☐ |
| 1x2 board, 8 ft (Hardwood) | 3 each | ☐ |
| 5-1/4" base moulding, 8 ft | 1 each | ☐ |
| 1/4" x 2-1/2" hobby boards, 8 ft Door detailing. | 3 each | ☐ |
| Full-overlay frameless hinges | 3 set | ☐ |
| Basic hinges | 5 set | ☐ |
| Pocket-hole screws, 1-1/4" | 50 each | ☐ |
| Brad nails, 5/8", 1-1/4", 2" | 120 each | ☐ |
| Wood filler and glue | 12 oz | ☐ |
| Paint or stain and finish | 32 oz | ☐ |
Overall cost: $$$$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Drill / Driver, Pocket Hole Jig, Speed Square. Materials: 3/4" hardwood plywood, 4x8 sheet, Pocket-hole screws, 1-1/4"
Drill four 3/4" pocket holes in each end of each shelf and attach them to the sides to build the basic carcass. Keep it square — everything downstream references this box.
Tools: Brad Nailer. Materials: 3/4" hardwood plywood, 4x8 sheet, 1/4" plywood, 4x8 sheet, Brad nails, 5/8", 1-1/4", 2", Wood filler and glue
Center the drawer divider between the shelves and fasten it with glue and 1-1/4" brads — it also houses the optional drawers. Then nail the 1/4" back on with glue, using it to square up the armoire.
Tools: Brad Nailer, Miter Saw. Materials: 1x4 board, 4 ft, 1x3 board, 8 ft, 1x2 board, 8 ft, Brad nails, 5/8", 1-1/4", 2", Wood filler and glue
Start with the header trim, fastened to both top and sides with 2" nails and glue. Add the bottom side trim to the sides and shelves. Attach the side crown pieces together then to the sides, and add the front crown the same way. Measure and cut each piece to the real openings as you go.
Tools: Brad Nailer, Jigsaw, Miter Saw. Materials: 5-1/4" base moulding, 8 ft, Brad nails, 5/8", 1-1/4", 2", Wood filler and glue
Miter the base moulding to fit the sides, then measure and cut the front piece, mitering out both ends. Attach with 1-1/4" nails and glue. Cut the shaped footer profile with a jigsaw.
Tools: Brad Nailer, Drill / Driver. Materials: 1/2" hardwood plywood, half sheet, 1/4" x 2-1/2" hobby boards, 8 ft, Full-overlay frameless hinges, Basic hinges, Brad nails, 5/8", 1-1/4", 2"
Cut the door pieces. Glue and clamp the top and bottom hobby-board trim to each 1/2" plywood door back with 5/8" brads and let dry flat, then add the side trim. For fold-flat doors, measure and cut the ~36" top side trim and hang it with frameless full-overlay hinges so it can extend 90°.
Tools: Drill / Driver, Random Orbit Sander. Materials: Wood filler and glue, Paint or stain and finish
If adding drawers, note they're designed for the flat-folding doors — for non-flat-folding doors, cut the drawer bottoms and sides at 15" instead. Build and fit the drawers. Then fill all holes, let dry, sand, and finish; if staining, edge-band any exposed plywood edges.