NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A leaning ladder desk — a writing surface plus graduated shelves that rest against the wall on 5°-raked legs. Small footprint, no wall anchoring needed to stand.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Desk surface (1x6) | 1 | 3/4" × 5 1/2" × 31" | 1x6 | ☐ |
| Shelves (1x8) | 3 | 3/4" × 7 1/4" × 31" | 1x8 | ☐ |
| Shelf backs | 3 | 3/4" × 2 1/2" × 31" | 1x3 | ☐ |
| Shelf sides (short) | 2 | 3/4" × 2 1/2" × 6 1/4" | 1x3 | ☐ |
| Shelf sides (mid) | 2 | 3/4" × 2 1/2" × 8" | 1x3 | ☐ |
| Shelf sides (deep) | 2 | 3/4" × 2 1/2" × 15 1/4" | 1x3 | ☐ |
| Frame legs Both ends 5°, parallel, long point to short point. | 2 | 3/4" × 2 1/2" × 76 1/4" | 1x3 | ☐ |
| Frame rails | 2 | 3/4" × 2 1/2" × 32 1/2" | 1x3 | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 1x8, 8 ft (Pine) Shelves. | 1 each | ☐ |
| 1x6, 31" (Pine) Shelf. | 1 each | ☐ |
| 1x3, 8 ft (Pine) Frame, legs, shelf backs/sides. | 4 each | ☐ |
| Finish nails or staples, 1-1/4" | 60 each | ☐ |
| Wood screws, 1-1/4" | 16 each | ☐ |
| Wood glue | 4 oz | ☐ |
Overall cost: $$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Brad Nailer. Materials: 1x8, 8 ft, 1x6, 31", 1x3, 8 ft, Finish nails or staples, 1-1/4", Wood glue
Build all the shelf boxes first. Attach the backs, then the sides, with 1-1/4" nails or staples and wood glue. The shelves step from deep at the bottom to shallow at the top to suit the lean.
Tools: Miter Saw. Materials: 1x3, 8 ft
Cut the top back corner off each leg, leaving a 2-1/2" flat that is square to the top of the leg. This flat is what the back support lands on so the desk meets the wall cleanly despite the lean.
Tools: Brad Nailer, Drill / Driver. Materials: 1x3, 8 ft, Finish nails or staples, 1-1/4", Wood glue
Attach the back support (top rail) to the tops of the legs, matching the square cut from the previous step. Then attach the shelves to the legs at their heights.
Tools: Drill / Driver, Random Orbit Sander, Speed Square. Materials: 1x3, 8 ft, Wood screws, 1-1/4"
Lean the desk against the wall in its final position. Place the remaining bottom rail level with the floor — it will NOT be square to the raked legs, and that's correct: the legs lean, so the rail follows the floor, not the legs. Screw it in place, then sand and finish.