NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A padded, fabric-wrapped headboard built like a small stud-wall frame — stands on the floor behind any bed.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Top and bottom rails Adjust to your headboard's desired width, up to 96in. | 2 | 1 1/2" × 3 1/2" × 62" | 2x4 | ☐ |
| Vertical studs Height minus 3in — adjust to your desired finished height, up to 48in. | 4 | 1 1/2" × 3 1/2" × 45" | 2x4 | ☐ |
| Mounting cleats For securing the finished headboard to the wall or bed frame. | 2 | 1 1/2" × 3 1/2" × 20" | 2x4 | ☐ |
| Face panel | 1 | 1/4" × 62" × 45" | 1/4" plywood | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| Construction lumber, 2x4, 8 ft The frame — rails and uprights. | 2 each | ☐ |
| 1/4" plywood or wood paneling, 4x8 sheet Cut down to the frame's face size. | 1 each | ☐ |
| 2-3/4" screws Frame assembly. | 16 each | ☐ |
| 1-1/4" screws or staples Attaches the plywood panel to the frame. | 20 each | ☐ |
| Batting or old comforters Padding. | 3 yard | ☐ |
| Upholstery fabric, 54" width | 2 yard | ☐ |
| Staples | 1 box | ☐ |
Overall cost: $$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Circular Saw, Drill / Driver, Tape Measure. Materials: Construction lumber, 2x4, 8 ft, 2-3/4" screws
Build a rectangular 2x4 frame sized to your desired headboard width and height, using the two rails and four vertical studs, fastened with the 2-3/4" screws.
Square the frame before you drive the last few screws — an out-of-square frame telegraphs straight through the plywood, padding, and fabric to the finished piece.
Tools: Drill / Driver. Materials: Construction lumber, 2x4, 8 ft, 2-3/4" screws
Attach the two mounting cleats to the back of the frame now, while it's easy to get a drill square to the work. These are what let you secure the finished headboard to a wall or bed frame later.
Tools: Drill / Driver, Staple Gun. Materials: 1/4" plywood or wood paneling, 4x8 sheet, 1-1/4" screws or staples
Cut the plywood panel to the frame's outer size and fasten it to the front of the frame with glue and screws or staples.
Tools: Staple Gun. Materials: Batting or old comforters, Staples
Layer batting (or old comforters, doubled up) over the face panel and staple it to the back of the frame, pulling it snug but not so tight it compresses flat — you want a soft dome, not a hard board.
Tools: Staple Gun. Materials: Upholstery fabric, 54" width, Staples
Center the fabric over the padded panel. Staple the bottom edge first, then pull taut and staple the top, then the sides, working from the center of each edge outward.
Fold each corner neatly like wrapping a gift box rather than bunching it — a bunched corner is the one detail that gives away a home upholstery job at a glance.
Tools: Drill / Driver
Stand the finished headboard behind the bed and secure it to the wall with a French cleat, or fasten it to the bed frame itself through the mounting cleats, so it can't tip forward.