Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.

Easy-to-Build Bookcase – Metric

This bookcase offers ample storage and display space in a compact footprint.

Difficulty: Easy
Time: 2.8–5.5 hours
Cost: $$

Cut list

Part	Qty	T × W × L	Material	✓
Leg	4	38" × 38" × 953"	—	☐
Long Rail	4	38" × 38" × 813"	—	☐
Short Rail	4	38" × 38" × 235"	—	☐
Top and Bottom Shelf	2	19" × 235" × 889"	—	☐
Middle Shelf	2	19" × 235" × 889"	—	☐
Shelf Divider	2	19" × 235" × 260"	—	☐
Top Shelf Divider	1	19" × 235" × 279"	—	☐

Materials

Item	Qty	✓
Board, 38mmx 38mm 2400mm	4 board	☐
Board, 19mm x 235mm 1800mm	2 board	☐
Board, 19mm x 235mm 1200mm	1 board	☐
Box of 100 - 32mm coarse-thread pocket-hole screws	1 each	☐
Box of 50 - 64mm coarse-thread pocket-hole screws	1 each	☐
50 - paint-grade pocket-hole plugs (optional)	1 each	☐
Wood Glue	1 each	☐
Right-angle drill attachment	1 each	☐

Overall cost: $$. Lumber varies by region, species, and season, so we give a band rather than a figure.

Tools

Drill / Driver
Pocket Hole Jig
Bar / Pipe Clamps — optional
Combination Square — optional

Instructions

1. Make the Frame Parts
- Cut four Long Rails, four Legs and four Short Rails from 38mm x 38mm pine boards, as shown in the cutting diagram.
- Set your pocket-hole jig for 38mm-thick material and drill pocket holes at the ends of the Long Rails and Short Rails, as shown.
- Next, set your pocket-hole jig for 19mm-thick material.
- Then drill pocket holes centered on one side of each of the Short Rails as shown. These holes will be sued to help attach the shelves later. When you’re done, sand the parts smooth using 120-grit, then 150-grit sandpaper.
2. Assemble a Pair of Frames
- Position two Long Rails between two Legs, so that the upper Long Rail sits flush with the tops of the Legs, and the other Long Rail is located 57mm up from the bottoms of the Legs, as shown.
- Now attach the Long Rails using 64mm coarse-thread pocket-hole screws, as shown.
- Repeat this process to assemble the other frame. If you plan finish your shelves like we did—with clear finish on the frames and paint on the shelves and dividers—this is a good time to apply finish to the frame assemblies and the short dividers.
3. Make the Shelves and Dividers
Cut four Shelves, two Shelf Dividers, and one Top Shelf Divider from 1x10 poplar boards, as shown in the cutting diagram. With your pocket-hole jig set for 19mm-thick material, drill pocket holes where shown in the Top and Bottom shelves, the Middle Shelves, and the three Dividers. When you’re done, sand these parts smooth. If you plan to paint the shelves and dividers, as we did, this is a good time to do it. Yes, it means you’ll have to wait for the paint to dry before moving on with assembly, but you’ll save time in the long runs since painting now is much easier.
4. Attach Short Rails to Shelves
- Once your paint and finish are dry, you can move on with assembly.
- Glue and clamp two Short Rails to the Bottom Shelf as shown. Make sure the pocket hole on the side of each Short Rail faces inward. Secure each Short Rail to the Bottom Shelf using one 32mm coarse-thread pocket-hole screw.
- Repeat the process for Top Shelf.

Cut two 260mm-long spacers from 38mm x 38mm boards. Rest those spacers on the Legs and against the Bottom Shelf, as shown.
Position the Middle Shelf so it rests on the Spacers. Secure the Middle Shelf using 32mm coarse-thread pocket-hole screws.
Next, position the Divider as shown. Use a square to make sure that the Divider is located accurately, and then attach the shelves using 32mm coarse-thread pocket-hole screws. Depending on your drill, you may not be able to fit the drill and driver bit between the shelves. That’s where aright-angle attachment, like the Kreg 90° Pocket-Hole Driver, can be handy.
Repeat this process to attach the second Middle Shelf and Divider, but this time offset the Divider from the opposite end of the shelf.

Easy-to-Build Bookcase – Metric

Cut list

Materials

Tools

Instructions

1. Make the Frame Parts

2. Assemble a Pair of Frames

3. Make the Shelves and Dividers

4. Attach Short Rails to Shelves

5. Attach the Bottom Shelf

6. Attach the Middle Shelves and Divid

7. Attach the Top Shelf and Divider

8. Attach the Second Frame