NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A rolling table with two open shelves and two fold-down leaves that swing up into a full round top — a side table that expands when you need it.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Legs | 4 | 1 1/2" × 1 1/2" × 26 1/4" | 2x2 | ☐ |
| End aprons | 2 | 3/4" × 3 1/2" × 15 3/4" | 1x4 | ☐ |
| End trim | 4 | 3/4" × 2 1/2" × 15 3/4" | 1x3 | ☐ |
| Shelves | 2 | 3/4" × 15 3/4" × 28" | 3/4" plywood | ☐ |
| Side aprons | 2 | 3/4" × 3 1/2" × 28" | 1x4 | ☐ |
| Side trim | 4 | 3/4" × 2 1/2" × 28" | 1x3 | ☐ |
| Tabletop and leaves Two planks form the center panel, one plank each leaf. | 4 | 3/4" × 11 1/4" × 42" | 1x12 | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 2x2 board, 8 ft (Pine) Legs. | 2 each | ☐ |
| 1x4 board, 8 ft (Pine) Aprons. | 1 each | ☐ |
| 1x3 board, 8 ft (Pine) Shelf trim. | 2 each | ☐ |
| 1x12 board, 8 ft (Pine) Tabletop and leaves. | 2 each | ☐ |
| 3/4" plywood, half sheet Shelves. | 1 each | ☐ |
| Basic hinges Hinge the two leaves to the center panel. | 2 pair | ☐ |
| 8" drop-leaf supports | 2 pair | ☐ |
| 2" caster wheels Plate-mount, not bolt-through — the bolts can hit the shelf-trim pocket screws. | 4 each | ☐ |
| Pocket-hole screws, 1-1/4" | 50 each | ☐ |
| Wood glue | 4 oz | ☐ |
Overall cost: $$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 2x2 board, 8 ft, 1x4 board, 8 ft, Pocket-hole screws, 1-1/4", Wood glue
Build the two end assemblies, keeping insides flush and hiding the 3/4" pocket holes to the insides, joined with 1-1/4" pocket screws and glue. Drill 3/4" pocket holes facing upward on the insides of the top aprons now, for grabbing the tabletop later.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 3/4" plywood, half sheet, Pocket-hole screws, 1-1/4"
Drill 3/4" pocket holes all around both shelves and attach them to the legs per the layout.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 1x4 board, 8 ft, 1x3 board, 8 ft, Pocket-hole screws, 1-1/4"
Add the side trim with 3/4" pocket holes and 1-1/4" screws, fastening the shelves to the corresponding trim as well. Remember to drill upward-facing pocket holes in the top aprons before you attach them, for the tabletop.
Tools: Drill / Driver, Jigsaw, Pocket Hole Jig. Materials: 1x12 board, 8 ft, Basic hinges, Pocket-hole screws, 1-1/4", Wood glue
Build the center tabletop panel with a row of pocket holes down the center and glue. Hinge the two leaves to it so the whole thing opens into a big square. Draw an arc across the entire assembly, open, and cut the circle with a jigsaw so the curve flows across the leaf seams. Attach the center panel to the base through the upward pocket holes.
Add the four casters to the bottom — use plate-mount ones so their fasteners don't collide with the bottom-shelf trim pocket screws. Install the 8" drop-leaf supports under each leaf so it locks level when raised. Sand and finish.