NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A storybook-crooked doghouse — the tilted, off-kilter look comes from four genuinely different truss angles, not from sloppy building.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Truss top members, long Top end cut at 45° off square, long-point measurement. | 6 | 1 1/2" × 1 1/2" × 34 1/2" | Pine | ☐ |
| Truss top members, short Top end cut at 45° off square, long-point measurement. | 6 | 1 1/2" × 1 1/2" × 30 1/2" | Pine | ☐ |
| Truss bottom chords Both ends cut at 10° off square, NOT parallel, long-point measurement. | 4 | 1 1/2" × 1 1/2" × 29" | Pine | ☐ |
| Truss angled braces, set A 30°/10° compound ends, long-point measurement. | 4 | 1 1/2" × 1 1/2" × 23 3/4" | Pine | ☐ |
| Truss angled braces, set B 40°/10° compound ends, long-point measurement. | 4 | 1 1/2" × 1 1/2" × 21 3/8" | Pine | ☐ |
| Floor | 1 | 1/2" × 29" × 39" | Exterior plywood | ☐ |
| Ridge supports | 2 | 1 1/2" × 1 1/2" × 48" | Pine | ☐ |
| Side panel, lower | 1 | 1/2" × 39" × 19 1/4" | Exterior plywood | ☐ |
| Side panel, upper | 1 | 1/2" × 39" × 22" | Exterior plywood | ☐ |
| Front/back gable panels Curved gable shapes cut from these — trace the pattern, don't eyeball it. | 2 | 1/2" × 42 3/8" × 40 3/8" | Exterior plywood | ☐ |
| Side trim | 2 | 3/4" × 2 1/2" × 37" | Pine | ☐ |
| Side trim, lower | 2 | 3/4" × 1 1/2" × 18 3/4" | Pine | ☐ |
| Side trim, upper | 2 | 3/4" × 1 1/2" × 21 1/2" | Pine | ☐ |
| Front/back trim, straight Both ends 10° off square, long-point, NOT parallel. | 2 | 3/4" × 2 1/2" × 29 3/4" | Pine | ☐ |
| Front/back trim, angled A 40°/10° compound, long-point. | 2 | 3/4" × 2 1/2" × 23" | Pine | ☐ |
| Front/back trim, angled B 30°/10° compound, long-point. | 2 | 3/4" × 2 1/2" × 25 1/4" | Pine | ☐ |
| Door trim, top | 1 | 3/4" × 2 1/2" × 25 3/4" | Pine | ☐ |
| Door trim, sides One end of each cut at 5° off square, long-point. | 2 | 3/4" × 2 1/2" × 18 1/2" | Pine | ☐ |
| Roof panels One side 48" x 36", the other 48" x 32" — the crooked roofline doesn't match side to side. | 2 | 1/2" × 36" × 48" | Exterior plywood | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| Exterior plywood, 1/2", 4x8 sheet 2-1/2 sheets called for; buy 3 to allow for cutting waste on the angled panels. | 3 each | ☐ |
| Pine or fir, 2x2, 8 ft Trusses and roof supports. | 11 each | ☐ |
| Pine, 1x3, 8 ft | 4 each | ☐ |
| Pine, 1x2, 8 ft | 1 each | ☐ |
| Pocket hole screws, 2-1/2" | 1 box | ☐ |
| Finish nails, 1" | 1 box | ☐ |
| Wood glue, exterior/waterproof This lives outside — use a waterproof formula, not standard interior glue. | 8 oz | ☐ |
| Wood screws, 2" and 3" | 1 box | ☐ |
Overall cost: $$$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Drill / Driver, Miter Saw. Materials: Pine or fir, 2x2, 8 ft, Wood glue, exterior/waterproof
Glue and fasten each truss with countersunk screws, driving pilot holes into the ends before assembly so the screws don't split the 2x2 stock. Every truss uses a different angle combination, so keep your cut pieces labeled and match them to the right truss.
Tools: Drill / Driver. Materials: Exterior plywood, 1/2", 4x8 sheet, Wood glue, exterior/waterproof
Mark the truss locations on the floor panel. Apply glue to the tops of the panel where each truss lands, then screw down through the floor into each truss with 2" screws.
Materials: Exterior plywood, 1/2", 4x8 sheet, Wood glue, exterior/waterproof
Attach the two end panels to the trusses as shown, using glue at every joint.
Tools: Drill / Driver. Materials: Exterior plywood, 1/2", 4x8 sheet, Wood screws, 2" and 3"
Attach the lower and upper side panels using 2" screws and glue.
Tools: Brad Nailer. Materials: Pine, 1x3, 8 ft, Finish nails, 1"
Trim out the sides using 1" finish nails and glue. The stated measurements run to the center of each stud, which makes for easier, more accurate nailing than measuring to a board edge.
Tools: Brad Nailer
Trim out the front and back panels the same way, following the angled measurements exactly — this is where a sloppy cut turns "charmingly crooked" into "actually doesn't fit."
Tools: Brad Nailer. Materials: Pine, 1x3, 8 ft
Trim out the front door opening with glue and 1" finish nails.
Tools: Drill / Driver. Materials: Pine or fir, 2x2, 8 ft
Attach the front and back overhang trusses, making sure to join the tops with screws and glue. If you want extra support, add ridge poles between the trusses — not strictly required, but cheap insurance on a roof this shape.
Tools: Drill / Driver. Materials: Exterior plywood, 1/2", 4x8 sheet
Attach the two roof plywood panels last. Because the truss angles differ, the two roof panels are different sizes — double-check you're installing the right one on the right side before you commit any fasteners.