NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A solid four-drawer dresser built almost entirely from construction-grade 2x4s and pocket screws. Cheap lumber, real furniture.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Legs | 4 | 1 1/2" × 3 1/2" × 29 1/2" | 2x4 | ☐ |
| Side top/bottom rails Trim to fit once the side infill panels are built — actual 2x4 width varies. | 4 | 1 1/2" × 3 1/2" × 14" | 2x4 | ☐ |
| Side panel infill pieces Fill each side between the top and bottom rails. Pocket holes on the inside face. Or substitute a plywood panel for a flat-panel look. | 4 | 1 1/2" × 3 1/2" × 22 1/2" | 2x4 | ☐ |
| Front and back rails Pocket holes hidden top and bottom. Cut to fit your actual carcass width. | 4 | 1 1/2" × 3 1/2" × 14" | 2x4 | ☐ |
| Top boards Glued up edge to edge; the length gives a ~3/4" overhang each end. | 4 | 1 1/2" × 5 1/2" × 22 1/2" | 2x6 | ☐ |
| Large drawer front/back | 4 | 3/4" × 5 1/2" × 15 1/2" | 1x6 | ☐ |
| Large drawer sides | 4 | 3/4" × 5 1/2" × 16" | 1x6 | ☐ |
| Small drawer false front 1/4" narrower than the opening; measure your real opening and cut to fit. | 1 | 3/4" × 5 1/2" × 17 3/4" | 1x6 | ☐ |
| Large drawer false fronts 1/4" narrower than the opening; measure and cut to fit. | 2 | 3/4" × 7 1/4" × 17 3/4" | 1x8 | ☐ |
| Back panels Sized with ~1" overlap onto the frame all around. | 2 | 1/4" × 12" × 17 1/2" | 1/4" plywood | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 2x4, 8 ft (SPF / Pine) Legs, rails, and the side infill panels. Pick the straightest, driest boards you can find. | 8 each | ☐ |
| 2x6, 8 ft (SPF / Pine) The four boards for the top. | 2 each | ☐ |
| 1x6, 8 ft (Pine) Small drawer front and drawer box sides/backs. | 2 each | ☐ |
| 1x8, 8 ft (Pine) The two large drawer fronts. | 1 each | ☐ |
| 1/4" plywood Drawer bottoms and the back panels. A half sheet is plenty. | 1 sheet | ☐ |
| Side-mount drawer slides Buy the slides first — the drawer boxes are built to fit them, not the other way around. | 4 pair | ☐ |
| Pocket hole screws, 1-1/4" and 2-1/2" Coarse-thread for softwood. | 1 box | ☐ |
| Wood screws, 1-1/4" | 1 box | ☐ |
| Wood glue | 8 oz | ☐ |
| Finishing nails, 3/4" For pinning the back panels. | 1 box | ☐ |
| Drawer pulls or knobs | 3 each | ☐ |
| Wood filler, pre-stain conditioner, and finish The pictured piece used a pre-stain conditioner, a stain, and a matte poly. | 1 kit | ☐ |
Overall cost: $$$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 2x4, 8 ft, Pocket hole screws, 1-1/4" and 2-1/2"
Make each side infill from four 2x4s laid face to face, with pocket holes drilled on the inside so they disappear once assembled. Drill a pocket hole into the top and bottom of each infill panel too — that's how the panel ties into the top and bottom rails.
If you'd rather have a smooth, flat side, drop in a plywood panel here instead. Build both sides identical before you go further.
Tools: Drill / Driver, Speed Square, Tape Measure. Materials: 2x4, 8 ft, Pocket hole screws, 1-1/4" and 2-1/2"
Attach a 29.5" leg to each end of a side panel, then cap the panel with the 14" top and bottom rails.
Here's the gotcha: a 2x4 is rarely exactly 3.5" wide, and four of them glued up rarely add to exactly what the drawing says. Measure the panel you actually built and trim the 14" rails to suit. Force the drawing onto reality and the case ends up out of square.
Tools: Drill / Driver, Pocket Hole Jig, Speed Square. Materials: 2x4, 8 ft, Pocket hole screws, 1-1/4" and 2-1/2"
Join the two side assemblies with the back rails, pocket holes facing in so they're hidden from behind. Drill the pockets on the narrow (1.5") face of each rail.
Check the case for square across both diagonals before you move to the front — everything downstream depends on this box being true.
Tools: Drill / Driver, Pocket Hole Jig.
Install the front rails to define the drawer openings. Put the top rail's pocket holes on top (hidden by the top) and the bottom rail's underneath. Drill the pockets on the narrow end of each piece.
The openings these rails create are what the drawers fit into, so keep them even side to side.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 1x6, 8 ft, 1/4" plywood, Pocket hole screws, 1-1/4" and 2-1/2"
Drill pocket holes in both ends of the 15-1/2" drawer front/back pieces, then join them to the 16" sides to form each box. Either rout a groove for a 1/4" plywood bottom or simply fasten the bottom to the underside of the box.
Build the boxes to the width your slides need, not to a nominal number — most side-mount slides want exactly 1" total clearance (1/2" per side).
Tools: Drill / Driver, Tape Measure. Materials: Side-mount drawer slides
Follow the instructions that came with your slides to mount them to the drawer boxes and the case. As a rule you'll want about a 1/2" gap between the bottom of a drawer and the rail beneath it, but the slide instructions are the authority here.
Test each drawer for smooth travel before adding fronts.
Tools: Drill / Driver, Tape Measure. Materials: 1x6, 8 ft, 1x8, 8 ft, Wood screws, 1-1/4"
Fit the false fronts to the openings with an even reveal at the top and outer edges — the small front is the 1x6 at ~17-3/4", the large fronts are the 1x8s. Measure your real openings and cut to fit; don't trust the nominal number.
Drill two holes through the drawer box from inside, position the false front exactly where you want it, and screw out through the box into the front with 1-1/4" screws. Floating the fronts this way is what gives you dead-even gaps even if a box is slightly off.
Tools: Drill / Driver, Pocket Hole Jig. Materials: 2x6, 8 ft, Pocket hole screws, 1-1/4" and 2-1/2", Wood glue
Edge-glue the four 2x6s into a top ~22.5" long, so it overhangs about 3/4" on each side.
Drill pocket holes on the side and back rails facing up, and drill down through the front rail. Lay the finished top face-down, set the upturned case on it with an even overhang all around, then fix the sides and back with 1-1/4" pocket screws and the front edge with 2-1/2" screws up through the front rail.
Materials: Finishing nails, 3/4"
Drop the 1/4" back panels in from inside, leaving at least a 1/2" gap around the edge, and pin them with 3/4" finishing nails. The panels are sized to overlap the frame about 1" all around.
Tools: Random Orbit Sander. Materials: Drawer pulls or knobs, Wood filler, pre-stain conditioner, and finish
Sand everything well to knock down the joints and clean off glue squeeze-out — construction lumber needs this more than nice hardwood does. Apply a pre-stain conditioner (pine blotches badly without it), then your stain or paint and a protective topcoat.
Temporarily pull the drawer fronts, drill for your pulls, and reinstall. Done.