NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
A footed cedar planter built as four picket panels pocket-screwed to 2x2 legs — with a false bottom, because no plant needs two feet of dirt.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Panel rails Two per panel, plus two spares for the false-bottom cleats. | 10 | 3/4" × 2 1/2" × 17" | 1x3 | ☐ |
| False-bottom cleats and slats | 5 | 3/4" × 1 1/2" × 17" | 1x2 | ☐ |
| Legs | 4 | 1 1/2" × 1 1/2" × 23 3/4" | 2x2 | ☐ |
| Panel pickets 1/4" shorter than the diagrams to allow for the saw kerf and trimming off the dog-eared ends. | 12 | 5/8" × 5 1/2" × 17 3/4" | Cedar fence picket | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| Cedar fence picket, 5-1/2" x 72" (Cedar) Twelve panel pickets from three boards. | 3 each | ☐ |
| 1x3, 8 ft Panel rails, top and bottom. | 2 each | ☐ |
| 1x2, 8 ft False-bottom cleats and slats. | 1 each | ☐ |
| 2x2, 8 ft The four legs. | 1 each | ☐ |
| Exterior pocket hole screws, 2-1/2" | 32 each | ☐ |
| Galvanized nails or exterior screws, 1-1/4" Pickets to rails. | 60 each | ☐ |
| Exterior wood glue | 4 oz | ☐ |
Overall cost: $. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Brad Nailer, Speed Square, Tape Measure. Materials: Cedar fence picket, 5-1/2" x 72", 1x3, 8 ft, Galvanized nails or exterior screws, 1-1/4", Exterior wood glue
Nail and glue three pickets to two 1x3 rails per panel, working from the inside face so the fasteners don't show. Leave an 1/8" gap between pickets — cedar pickets are wet off the rack and WILL move, and the gap is where that movement goes instead of into a bowed panel.
Don't chase perfection here. The pickets aren't perfect and the design knows it.
Tools: Drill / Driver, Pocket Hole Jig
On the inside of every panel, drill two 1-1/2" pocket holes behind each 1x3 rail end. The screws will run through picket and rail into the legs — that stack is the whole joint, so drill at the rail ends where the material is.
Tools: Drill / Driver. Materials: 2x2, 8 ft, Exterior pocket hole screws, 2-1/2"
Attach two opposite panels to the four legs with the 2-1/2" exterior pocket screws, panels flush to the leg faces per the diagram. Work on a flat surface so the legs all land level.
Tools: Drill / Driver, Tape Measure. Materials: Exterior pocket hole screws, 2-1/2"
Add the remaining two panels the same way. Before the final screws go in, check the planter for square across the top opening and rack it true — pocket screws allow one round of adjustment, then they're committed.
Tools: Drill / Driver, Random Orbit Sander. Materials: 1x2, 8 ft, Galvanized nails or exterior screws, 1-1/4"
You are not growing potatoes — don't fill the whole planter with dirt. Screw 1x2 cleats around the inside about 6" down from the rim (or deeper for bigger root balls), then lay 1x2 slats across them with drainage gaps.
Line with landscape fabric to keep soil off the cedar, plant, and set it somewhere it gets admired. Sand and break the top edges first — hands land on the rim every time someone waters it.