NotchLoading plan…
Loading plan…
Use your browser's Print (Ctrl/Cmd + P) and choose Save as PDF. This page works offline once you've opened it with a signal.
Notched-stringer stairs sized by a rise/run calculation, not a fixed cut list — this plan walks the math on a worked two-step example.
| Part | Qty | T × W × L | Material | ✓ |
|---|---|---|---|---|
| Stringers Length is generous stock to notch from — mark and cut your rise/run pattern per your own calculated numbers, not this length directly. | 2 | 1 1/2" × 11 1/4" × 30" | 2x12 | ☐ |
| Ledger / back board Set stair width to 36" here; adjust to your own opening. | 1 | 1 1/2" × 5 1/2" × 36" | 2x6 | ☐ |
| Tread boards Two boards per tread for a two-step run, laid side by side with a small gap. | 4 | 1 1/2" × 5 1/2" × 36" | 2x6 | ☐ |
| Item | Qty | ✓ |
|---|---|---|
| 2x12 board, 8 ft (Pressure-treated pine) Stringers. Use 2x10 or 2x8 instead if your rise/run cuts leave enough solid wood below the notches — 2x12 gives the most margin. | 2 each | ☐ |
| 2x6 board, 8 ft (Pressure-treated pine) One board for the ledger/back board, two for tread boards (two boards per tread, side by side, gives an 11" tread depth with a little nosing). | 3 each | ☐ |
| Deck screws, 3" | 30 each | ☐ |
Overall cost: $$. Lumber varies by region, species, and season, so we give a band rather than a figure.
Tools: Tape Measure
Measure the overall height your stairs need to cover and the width you want them. Divide the overall height by about 7 and drop the decimal — that whole number is how many steps (rises) you need. Divide the overall height by that number of rises to get the exact height of each step.
Then decide your tread depth. If it doesn't matter exactly where the stairs land, two 2x6 boards side by side gives about an 11" tread with a little nosing — an easy, comfortable default. If your stairs must land at a specific spot, divide your total available run by the number of treads instead.
Tools: Pencil, Speed Square. Materials: 2x12 board, 8 ft
Set your speed square (or rafter square) to your calculated rise and run measurements. Line the square up with the edge of the stringer board and trace the rise/run notch. This first stringer is your template for every following one, so take the time to get it right.
Tools: Circular Saw, Hand Saw. Materials: 2x12 board, 8 ft
Slide the square down the board, lining it up with your previous mark and the board's edge, and trace the next notch. Repeat for every step, then cut both stringers with a circular saw for the straight runs and a hand saw to finish each inside corner cleanly.
Tools: Drill / Driver, Level. Materials: 2x6 board, 8 ft, Deck screws, 3"
Screw the ledger/back board to the tops of both stringers, then attach that assembly to your landing or deck framing, checking it's level and that both stringers are plumb and evenly spaced for your stair width.
Tools: Drill / Driver, Level. Materials: 2x6 board, 8 ft, Deck screws, 3"
Starting at the bottom, screw down the first tread's two boards to the stringer notches, using a pencil laid on its side as a quick, repeatable gap spacer between the boards. Work your way up, checking each tread stays level, and screw every tread down securely.