NotchLoading plan…
Loading plan…
This hutch is a simple open box divided into two zones by a single off-center vertical divider: a shelved section on one side for books or bins, and a taller open section on the other for anything that doesn't fit a fixed shelf height. Building the top, sides, and divider as one assembly first — before the shelf and the smaller dividers inside the shelving zone go in — keeps the main structure easy to square up while it's still a simple open frame.
The shelving-area dividers and the plywood back are both called out as "cut to fit" rather than fixed dimensions, because small variations in how square your main assembly comes out will shift those numbers slightly. Measure your actual opening at that stage rather than trusting the plan's number to the fraction.
| Item | Qty |
|---|---|
| 1x10 board, 4 ft | 1 each |
| 1x10 board, 8 ft | 1 each |
| 1x3 board, 4 ft | 1 each |
| 1/4" backing material (plywood, MDF, or paneling), quarter sheet | 1 each |
| Pocket-hole screws, 1-1/4" | 30 each |
| Brad nails, 1-1/4" and 3/4" | 40 each |
| Wood glue | 2 oz |
Overall cost: $$. Lumber prices vary by region, species, and season, so we give a band rather than a figure we would only be pretending to know.
| Part | Qty | T × W × L |
|---|---|---|
| Top1x10 | 1 | 3/4" × 9 1/4" × 47 1/2" |
| Vertical sides and divider1x10 | 3 | 3/4" × 9 1/4" × 15 1/4" |
| Shelving-area base1x3 | 1 | 3/4" × 2 1/2" × 17 1/4" |
| Open-area base1x3Updated inside width — this side is 27-1/2", not 21". | 1 | 3/4" × 2 1/2" × 27 1/2" |
| Shelving-area bottom1x10 | 1 | 3/4" × 9 1/4" × 17 1/4" |
| Shelving-area dividers1x10Cut to fit your assembled shelving opening. | 3 | 3/4" × 9 1/4" × 9 1/2" |
| Back panel1/4" backingCut to fit the assembled hutch's actual back opening. | 1 | 1/4" × 16" × 47" |
Buy 4 boards at 8 ft.
2 boards
1 board
1 board
Assumes 8 ft stock, a 1/8" saw kerf, and buying each part at its own width. Change the board size or kerf on the full board plan →
Attach the top to the two outer sides and the center divider, using 2" screws, 3/4" pocket holes with 1-1/4" pocket hole screws, or 1-1/4" brad nails and glue — this joint gets reinforced by the back panel later, so any of these methods works. The open area's inside width is 27-1/2", not 21" — use the updated number.
Attach the shelving-area base and the open-area base (updated to 27-1/2" long) across the bottom. Nailing works, but pocket holes are worth using at the center for extra strength. No Kreg jig? Nail or screw in at an angle instead.
Add the shelving-area bottom shelf, then the three interior dividers — same fastener choice as the base supports.
Measure the assembled hutch's actual back opening, cut the backing material to fit, and attach it with 3/4" brad nails and glue.
No reviews yet
Sign in to review this plan or share your build.
No reviews yet. Be the first to build this.